2. Fill in the values in the data RAM addresses specified for the following AVR code: LDI R18, $20 LDI R17, $0A RCALL DivideR18byR17 END1: 6 5 4 3 2 10 Address 7 RJMP END1 $200 $201 DivideR18byR17: $202 STS $200, R18 ; store Numerator $203 STS $201, R17 ; store denominator $204 CLR R16 ; clear quotient reg. DivLoop: INC R16 SUB R18, R17 BRCC DivLoop DEC R16 ADD R18, R17 STS $202, R16 STS $203, R18 RET

2. Fill in the values in the data RAM addresses specified for the following AVR code: LDI R18, $20 LDI R17, $0A RCALL DivideR18byR17 END1: 6 5 4 3 2 10 Address 7 RJMP END1 $200 $201 DivideR18byR17: $202 STS $200, R18 ; store Numerator $203 STS $201, R17 ; store denominator $204 CLR R16 ; clear quotient reg. DivLoop: INC R16 SUB R18, R17 BRCC DivLoop DEC R16 ADD R18, R17 STS $202, R16 STS $203, R18 RET

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Write the following in LC3 code: Write a program that compares two values stored at memory locations x30A2 and x30A3. If the value at x30A2 is larger than the value at x30A3 then store the value of 1 in R1, else store the value of 0 in R1.Use PC + offset addressing to load contents of x30A2 into R2 and x30A3 into R3. Repeat the previous using Base + offset (load register). Use the load immediate (LEA) instruction to set up the base (R4) with the address of x30A2
Create a program that uses the direct addressing method to store data DFH in RAM memory regions 30H through 39H.
Write a PIC18 instruction sequence to initialize the contents of file registers at addresses from 0x077 until 0X07A with the value D'120'. You MUST use indirect addressing mode with file select register, FSR2 in your solution.
Micropocessor 8051
subject is Microprocessor - Arithmetic Instructions
1. Write an instruction sequence to save the current content of the flag in memory location MEM1 and then reload the flags with the contents of memory location MEM2. LAHF MOV MEM1, AH MOV AH, MEM2 SAHF HLT 2. Verify the operation of the following instructions that affect carry flag, start with CF = 0. CLC STC СМС 3. Write an instruction sequence to configure the 8086 as follows: Interrupts not accepted; Save the original contents of flag SF,ZF,AF,PF and CF at the address [0700H], then Clear the carry.
Urgent
Segment registers are:Select one: a. Define the logical address с b. All the given options here C c. Shifted left when making the physical address d. 16 bits C e. SPR in the CPU Which statement in the following is wrong? Select one: a. Segment address and offset address are part of the physical address b. None of the options here C C C c. Segment address and offset address are part of the logical address d. Segment address defines which part of the memory we deal with e. Offset address defines which part in the segment we deal with XYZ is a defined bytes array containing 4F CA DC 55 E3 48 Select one: a. XYZ[4] is 55 b. XYZ[3] is DC c. XYZ[4] is CA d. None of the options here e. XYZ[4] is not existing in the array C с с C C
Find the N, Z, OV, DC, C flags and value stored in RAM address 0x010 for the followings: MOVLW 0xE9 MOVWF 0x10, 0 MOVLW 0xED MOVLB 0 ADDWF 0x10, 1