2. Evaluate the digital modulated signal given below and develop an output equation of the modulated signal for the second discrete level, if the total discrete levels are 6 and the frequency of the modulated signal is given as 1.1 MHz and Power per signal is 10 KWatt. 0 2 4 6 10

2. Evaluate the digital modulated signal given below and develop an output equation of the modulated signal for the second discrete level, if the total discrete levels are 6 and the frequency of the modulated signal is given as 1.1 MHz and Power per signal is 10 KWatt. 0 2 4 6 10

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 7VE

See similar textbooks

Similar questions

Find the outer radius of a coaxial cable whose characteristic impedance is 10Ω. The inner radius and the dielectric constant are 0.08m and 0.5 respectively.
A signal's spectrum contains four components: -2500 Hz, -1700 Hz, +1700 Hz, and +2500 Hz. If we assume this spectrum is the product of two sinusoidal signals, what are the frequencies of the two signals whose product gives rise to this spectrum? 400 Hz and 2100 Hz 1700 Hz and 2500 Hz 1300 Hz and 2100 Hz 800 Hz and 4200 Hz
(a) An aperiodic signal is defined as x(t) = sin(at) u(t), where u(t) is the continuous time step function. Discuss the periodicity property of the odd portion of this signal, xo(t).
Help me to solve this Find the equation for a sine wave signal with a frequency of 10 Hz, maximum amplitude of 20 volts, and phase angle of 0
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 18 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 2 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 600, compute for the primary peak voltage. D1 D2 D3 D4 v(Volts) v2 (seconds)
5
By using Laplace Transform for circuits analysis we O о Replace inductor with impedance sL, in parallel with its current source Replace inductor with impedance 1/sL, in series with its current source Replace inductor with impedance 1/sL, in parallel with its current source Replace inductor with impedance sL, in series with its current source
H.W a. Calculate the filter coefficients for a 5-tap FIR bandpass filter with a lower cutoff frequency of 2,000 Hz and an upper cutoff frequency of 2,400 Hz at a sampling rate of 8,000 Hz using the Fourier transform method. b. Determine the transfer function and difference equation of the designed FIR system.
Determine the information capacity in Mbps for a circuit with 100 kHz bandwidth and a signal-to-noise power ratio of 40 dB. (Use 2 decimal places for the final answer
2. In an opamp inverting amplifier circuit. Ri = 10 k2. and Ri = 2.2 ko. Find the output voltage when the input voltage is (a) +0.25 V
subject (electronics for computer engineering )
4. Consider the series RLC circuit in Homework 7, Question 2. The component values are R = 1 ohms, inductance = 0.3 henries, and capacitance C = 0.6 farads. Enter w (double-u) for w (omega). x(t) L C (a) Find the frequency response function H(w) Y(w) = X(w) H(w) = (b) Find the positive linear frequency fo = wo in Hz at which |H(w) = 1. This is the resonant frequency or the center frequency of the bandpass filter. fo = (c) Find the two positive frequencies f₁₁ = 1 and (fcı < fœ₂) in Hz, at which |H(w)| = fc2 = These are the half-power frequencies of the bandpass filter. fc₁ = fc₂ = R www y(t)