Answered: 2. Dynamic viscosity of the fluid is u…

2. Dynamic viscosity of the fluid is u = 8.0×10² Pa · S flow along the flat, the velocity gradient isdu dy 10°1/s |3| shear stress is ( ). А, 0.1Ра В, 0.8Ра C, 80PA D, 100PA.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q: Consider fully developed laminar flow in the annular space formed by the two concentric cylinders shown in the below diagram. The outer pipe is stationary, and the inner pipe moves in the x direction with speed V For pressure gradient, , and the inner cylinder stationary, let ro = R and r = kR, The velocity profile is ax given by: др + 4μ. θα Find: 1- Volume flow rate (Q). 2- An expression for the average velocity (V) 3- Fork → 0, find Q and V 6
I need the answer as soon as possible
If a force (p) of ( 7.8 ) N causes the 30 mm diameter shaft to slide along the lubricated bearing with a constant speed (y) of 1.4 m/s, determine the hydraulic shear stress (T) and dynamic viscosity ( Mu ) of the lubricant .Also , find the constant speed Ynew in m/s of the shaft when the magnititude of P is tripled value .The gap between the bearing and the shaft is1 mm and the width of the shaft (x) is 23 mm as shown in the figure bellow. 1.The hydraulic shear stress ( Tau) is------- The answer in kPa? 2. The value of the dynamic viscosity ( Mu ) in Pa.sec is? 3. The new speed of the shaft when the value of the force P has been tripled is The answer in m/sec?
A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (1) Calculate the Reynold's number Re=_________
cture.com/courses/22169/quizzes/88681/take A piston contains a type of fluid that has a S.G of 0.9 and a dynamic viscosity of 0.02 Poise. The flow at section B is 0.4mL/s. Considering that the velocity head and head losses in the pipe is neglected at section A, determine: a. The velocity at point B in m/s b. the Reynolds number at section B C. The required force to produce the given flow in Newtons d = 10 mm d 0.25 mm 20 mm 30 mm
Q1) When the force (P) applied to the plate shown in Fig.1,the velocity profile for a fluid is confined under the plate is approximated by u = 12 y0.25 mm/s ,where y is in mm. Calculate the shear stress at y 16 mm. Take u = 0.8x10 N.s/m2. 16 mm Fig.1
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
The Reynolds number, pVD/μ is a very important parameter in fluid mechanics. Determine its value for ethyl alcohol flowing at a velocity of 2 m/s through a 2-in.- diameter pipe. Re=
A pipe-line carrying water has average height of irregularities projecting from the surface of the boundary of the pipe as 0.15 mm. What type of boundary is it? The shear stress developed is 4.9 N/m². The kinematic viscosity of water is .01 stokes.
3:'A hydraulic oil is flowing in a horizontal drawn steel hydraulic tube ( ɛ = 1.5 x 10-6m) with an ID of 0.047m. A pressure difference of 68 kPa is || observed between two points in the tube 30 meters apart. The oil has a specific gravity of 0.90 and a dynamic viscosity of 3.0 × 10¬³P ·s. Calculate the velocity of the flow of oil using Method Il-C iteration.
Consider (Figure 1). The cord is attached to the 36-lb block, and the coefficients of static friction are HB = 0.2 and μp = 0.3. Figure M 1.5 ft B 3 ft -1.5 ft- D C < 1 of 1 Part A Determine the smallest couple moment which can be applied to the 24-lb wheel that will cause impending motion. Express your answer in pound-feet to three significant figures. VAΣo↓↑ vec M = Submit Provide Feedback Request Answer A ? lb-ft
A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046 m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (3) Calculate the drag force FD_________N (2 decimal places)