2. During an excavation for a tunnel, 250 m below ground level, a highly fractured siltstone rock mass with two major joint sets and many random fractures is encountered. The RQD from the rock cores is 55% and the average UCS is 92 MPa. The joints with average spacing of 75 mm are rather continuous with high persistence with apertures of 3-5 mm, and they are filled with silty clay. The joint surface walls are highly weathered, undulating, and slickensided. There is some water inflow into the tunnel estimated as 15 L/min per 10 m of tunnel length, with some outwash of joint fillings. Estimate RMR, Q and GSI. Assume a unit weight of 28 kN/m² for the rock mass.

2. During an excavation for a tunnel, 250 m below ground level, a highly fractured siltstone rock mass with two major joint sets and many random fractures is encountered. The RQD from the rock cores is 55% and the average UCS is 92 MPa. The joints with average spacing of 75 mm are rather continuous with high persistence with apertures of 3-5 mm, and they are filled with silty clay. The joint surface walls are highly weathered, undulating, and slickensided. There is some water inflow into the tunnel estimated as 15 L/min per 10 m of tunnel length, with some outwash of joint fillings. Estimate RMR, Q and GSI. Assume a unit weight of 28 kN/m² for the rock mass.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. Triaxial tests were carried out on 54-mm-diameter intact rock specimens. The applied confining pressures and the principal stress differences at failure are summarized below. Confining 0 5.0 10.0 15.0 20.0 25.0 pressure (MPa) Principal stress 59.5 87.5 116.0 139.5 167.5 192.5 difference (MPa) Plot ₁ against 63 at failure and determine the uniaxial compressive strength and the friction angle of the intact rock.
c. If modulus of elasticity of a rock body is 75 x 10° Pa, Specific Surface Energy (ys) is 6.3 x 1010 dynes/m and half the length of an internal crack (Ta) is 5.3 x 104. Then find out the critical stress (oc) for the crack propagation for this rock. (Hint: 1 Pa = 10° dynes/m?).
Question 4 The simply supported rectangular slab shown in Fig. Q4 is subjected to a load of 10kN/m. Find the collapse load factor. (Note: Slab dimensions in meters) 10 kNm/m 20 kNm/m Fig. Q4
Is a simple bend in the rock layers so that they are no longer horizontal.
A 12 m-diameter shaft is to be developed down to a depth of 600 m, where the in situ stress field is expected to be hydrostatic. The site characterization work indicates that the average density of the rock mass is 2550 kg/m3. The tests performed on the borehole cores in the area give the rock mass strength parameters to be UCS = 90 MPa, m= 31 , and GSI = 65. Smooth blasting will be applied to minimize the damage to the shaft walls. Determine if the strength of the shaft walls will be exceeded along its length, and if so, at what depth. 3) !3!
d) Explain the two (2) ways the presence of water can significantly reduce rock strength.
A saturated specimen of cohesionless sand was tested under drained conditions in a triaxial compression test apparatus and the sample failed at a deviator stress of 482 kN/m2 and the plane of failure made an angle of 60° with the horizontal. Find the magnitude of the principal major stress in kPa.
True or false
The foundations supporting two columns of a building are shown in Figure E9.16. An extensive soil investigation was not carried out, and it was assumed in the design of the foundations that the clay layer had a uniform thickness of 1.2 m. Two years after construction the building settled, with a differential settlement of 10 mm. Walls of the building began to crack. The doors have not jammed, but by measuring the out-of-vertical distance of the doors, it is estimated that they would become jammed if the differential settlement exceeded 24 mm. A subsequent soil investigation showed that the thickness of the clay layer was not uniform but varies, as shown in Figure E9.16. The owners would like to get an estimate of the expected total differential settlement and how long it will take before the doors become jammed. 780 kN| 780 kN Foundation A Foundation B 1.5 m x 1.5 m 1.5 m x 1.5 m Sand. 1.4 m 3 m 2.8 m 1.2 m Clay, m, = 0.7 m²/MN Gravel FIGURE E9.16
Q.6.2 Determine the factor of safety against sliding on fracture surface for water table at the conditions below. Tension Crack 2. Given: y= 25 kN/m S = 20 kN/m?; = 25° a = 45° ; 8 = 30° %3D %3D %3D Fracture Surface u 01 4.23 m
If a compression test on specimen showing a vertical stress of 46 this rock MPa and a vertical strain of 522x10-6. The radial strain is 106x10-6. Calculate the Rock Mass Modulus (in GPa) considering the factor EM/ER = 0.1.
Earth Sciences Downward force is 4000 kg and rotational force is 3000 kg. Contact surface area (cross sectional area) is 100 cm2. Also, the rock sample (diameter: 20 cm) is tested by a uniaxial compressive strength machine and the sample was cracked at 30000 kg. Answer the following questions:a. Find the resultant force acting on the rock formation.b. Find the bearing strength of the rock drilled.c. Can we drill under these circumstances?