2. Draw the shear and moment diagrams for each member of the frame. T 3' 5' B W = 2 kips/ft A

Q: 15 kips 15 kips A B в C D 60 in.- 40 in. 40 in.

A: let vertical support reactions are VA& VD ∑Fv=0VA+VD =30VA=VD=302=15 kips due to symmetric…

Q: Draw the shear and moment diagram by area method and compute the maximum bending stress in the steel…

A:

Q: Draw the shear and moment diagram of the following beams. Let P = 13 P k/ft A D Hinge - 2 ft→- - 2…

A:

Q: 5 kN/m А D В C 70 kN 70 kN - 3 m --5 m→- 3 m - – 5

A:

Q: Determine the internal shear and moment in the beam as a function of x throughout the beam. x is…

A:

Q: Q1-Draw shear force (S.F) and bending moment (B.M) diagrams. A is a roller and B is a hinge. 14 kN 9…

A: Given Data Draw shear force and bending moment diagram.

Q: draw the shear and moment diagram of the given beam. determine the maximum moment. Use Area method,

A: Given: P=45000 So, the udl weight is, w=0.125×45000=5625 lb/ft

Q: Determine the normal internal force and shear force, plus the bending moment in the beam at points C…

A: Bending moment: The algebraic sum of all the moments of the vertical forces acting on the beam is…

Q: 18 kN/m 6 kN A - 3 m

A: Given: A cantilever beam's span is 3.0 m, a point load of 6 KN is acting on the free end, and a…

Q: 15 kN 10 kN 6 kN D E 0.4 kN/m 4 m 7 m 6 m 8 m

A:

Q: Draw the shear and moment diagrams for the beam. Assume the support at B is a pin. (8 + N) kN/m A…

A:

Q: 4 kN/m 4.5 m- *Assume A to be rocker, B to be fixed support, and C to be internal hinge.

A:

Q: 7-14. Determine the normal force, shear force, and moment at a section passing through point D. Take…

A:

Q: Draw the LOAD (w) and the BENDING MOMENT (M) diagrams that correspond to the given shear force…

A: The Joints are named as below

Q: maximum shear

A:

Q: R/ For the beam showin the Pigure below, draw shear force and bending Moment diagrams M=25KN 5 50 KN…

A:

Q: Determine the internal shear and moment at point C of the beam shown

A:

Q: 1. Draw the Shear and Moment Diagram of the given beam. A 1m 1m B 2m 1m A 1m

A: Given data  A = 13 kN  B = 10 KN/m  Draw Shear Force Diagram (SFD) and Bending Moment Diagram (BMD)…

Q: Prob) Draw the sheat AND moment diagrams for the beam & loading shown. 160 KN 10m 30m RB = = 55 KN 4…

A: Given- An overhange beam carrying different loading system provided with hinge support at C and…

Q: The post below is supported by a pin at A and a weightless link BC post below, using the method of…

A: Given:Required:Magnitude of internal moment at D

Q: 8k 1.5 k/ft 40 k-ft 10 ft 30 ft 10 ft-

A: A loaded beam is given and it has been asked to draw shear force and bending moment diagram. Please…

Q: Draw the shear and moment diagrams for the beam. The supports A and B are a thrust bearing and…

A: Given :

Q: Where should a single 500-lb live load be placed on the beam so it causes the largest moment at D?…

A: Given: The live load is 500 lb. Consider the figure,

Q: A concentrated load P is applied on the multispan beam, please construct the bending moment…

A:

Q: A k 3m D B 6KN-MIE 1 1.5m 1.5m 5KN Point D is located just to the left of the roller support at B.…

A: An overhanging beam is given, with a hinge at the left end and supported on a roller at 3m from the…

Q: Replace the loading by an equivalent resultant force and couple moment acting at point O.

A: First, we draw the free body diagram:-

Q: Determine the internal force and moment

A: Consider the figure,

Q: A 2m- 10 KN 50 kN m B 3 m C X

A:

Q: 4 kips w = 3 kips/ft A В C D 4'- - 6'- 5'–

A:

Q: Draw the shear and moment diagram. | 12 kN 48 kN m B 41 a. Determine the shear value at 5 m from A.…

A:

Q: draw the shear & moment diagram for the frane 6 kN/m -6 kN 6m D 4m

A:

Q: -4 ft- -4 ft |C В 6 ft Determine the shear force at point b using method of section if w = 47.1lb/ft…

A:

Q: Derive the shear and moment equations for each beam segment. SHOW THE SOLUTION AND PROCESSS

A:

Q: Draw the shear and moment diagram of each structure, w=150N/m

A:

Q: wo A B L L

A:

Q: Use the portal method and determine (approximately) the reactions at A, B, C, and D of the frame.

A: Dividing the base shear failure column: B=F1+2F2+2F1+2F1+F1 F1=8/6=1.33 kips

Q: a) Draw Shear and Moment Diagrams, and determine the maximum moment A 5 KN/m' 2m B 3m 10 KN C Im 2m…

A:

Q: 7-14. Determine the normal force, shear force, and moment at a section passing through point D. Take…

A:

Q: Draw (approximately) the moment diagram for the girder EFGH. Use the portal method.

A: Portal method is used to calculate shear force and bending moment in frames members which are…

Q: 7-14. Determine the normal force, shear force, and moment at a section passing through point D. Take…

A: Given : w= 150 kn/m Determine the normal force, shear force and moment at a section passing through…

Q: Q1: Draw the shear and moment diagrams for each member of the frame. Assume the support at A is a…

A: The diagram is shown in the above figure. We have to draw the SFD and BMD of the each member in the…