2. Draw the influence lines for the support reactions and bending moment and for the shear and bending moment at section 1-1 of the beam shown in figure.

Q: Q1. A slider-crank mechanism is shown in Figure1. You should draw free body diagrams for ea moving…

A:

Q: solving and equating on each compenent x, y, and z we have -10 TAB 1 Tre TAD = 0 1425 -30 -TAD = O V…

A: The equations are given as:

Q: ENGINEERING

A:

Q: Given: F = {8k} N and - F= {- 8 k} N - 300 mm Find: The couple moment acting on the pipe assembly…

A:

Q: To facilitate shifting the position of a lifting hook when it is not under load, the sliding hanger…

A: Given data in question  Mass hanging  Distances  To find out  Magnitude of force in Newton at point…

Q: B 400 N 200 N E) FBD of pipe AB above. Fixed support at B. Thrust-bearing at A.

A:

Q: 6' A I 2' B 6' D 2' 3'- E 2

A:

Q: Determine the Maximum Deflection of the beam in millimeters unit. Use the Virtual Work Method.…

A:

Q: need quickest solution , Don't hold for long time it would be useless,And must include free body…

A: Determine the moment about point-A and point-B.

Q: A system of cables is shown and is in a state of equilibrium. Using equilibrium equation, solve for…

A: To find tension in cable AB

Q: 150 mm 140 mm 50 mm 60° 130 mm 45 600 N

A: Find the position vector: OA→=130cos30o+50i-130sin30o+140j+150kOA→=162.58i-205j+150k mm The force in…

Q: For the beam shown (E = 200 GPa, A=12 cm², I-9 cm¹), determine: a) Reactions at A and C. b) Draw the…

A:

Q: please solve the following questions using the picture provided. 1. Determine V@c and reactions at…

A: Determinea. Reaction at C, A and B. b. Draw the shear force and moment diagram. c. Maximum moment…

Q: 6. Draw the moment diagrams using the method of superposition 5 kN/m 20 kN m 40 kN -12 m-

A: Break the structure in UDL and Moments

Q: Find the moment (N-m) about point O. Each square is 1 m. on each side. F1 = 58 N F2 = 215 N C1 = 202…

A: To find moment about point O

Q: +y 500 N → +x Determine the x-direction component of the force. Include the appropriate sign (- or…

A:

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

A: To determine Forces at O and moment at O required to replace the system of loads Resultant load…

Q: Compute the moment of the force P = 287 N in point A in N-m. Assuming Counterclockwise positive.…

A: Given Data  Find the moment about A due to force P = 287 N  Consider counterclockwise positive

Q: wn, compute for the reaction at Joint B.

A: Taking moment about A RBx10 =(10x7)+(15x5)+(10x3) RBx10=70+75+30 RBX10=175 RB=17510 RB=17.5kN…

Q: The cantilever beam is loaded as shown in the figure. Derive the equations for the shear force (V)…

A: Shear equation:Vx=-4x       0<x<8'Vx=-48=-32k       8'<x<16'Mx=-2x2…

Q: X 7'in. 7 in. D 9 in. A 5 in. E N P B P y

A:

Q: The device shown is used to straighten bowed decking boards just prior to final nailing to the…

A: Given, r=507 mm s=175 mm α=2.1°β=15° Force=P

Q: The force F = 45O Ibs acts on the frame. Resolve this force into components acting along members AB…

A: From the given information we have to calculate the reaction at the member AB and AC

Q: T 2' 3' Y Action line of F -5'- D B X

A:

Q: In order to reduce the bending moment in the cantilever beam AB, a cable and counterweight are…

A: Bending moment- A bending moment is the reaction that occurs in a structural element when it is…

Q: Let a=4 ft, b=7 ft, c-2 ft and w-6.5 kips/ft. Construct the shear-force and bending-moment diagrams…

A:

Q: Problem: Replace the force system acting on the frame by an equivalent resultant force and couple…

A: Horizontal componentX=300cos30°+500    =300×0.8660+500     =759.8076 NVertical…

Q: How to layout simple curves by Deflection Angles? Outline the step by step process and show a…

A:

Q: Engineering Mechanics

A:

Q: Replace the force and torque system acting on the rectangular block by a key. Specify the magnitude…

A:

Q: For the given statically indeterminate beam find • Deflection diagram • Moment equation of the beam…

A:

Q: 5.) Consider the 2D beam supported by a roller at A and a pin at B. EXTERNAL FORCES a) Draw a FBD.…

A: Find:

Q: Ay = Cy= i i Determine the shear force acting at each of the following locations: (a) x = 0+ ft…

A: The given beam is shown below.

Q: In your response, please display the full computation and all FBDs that were used. Only round off at…

A:

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.