2. Determine the value and calculate the acceptable tolerance range ofthe resistor that shown in the figure bellow:3. Record resistor colors based on its value for the following:A. (9102 10%)В. (6.8KО 20%)4. Using the Multisim, connect the circuit shown in Fig. (1).Increase the voltage as shown in the table and measure current in each stepthen record it in table below:V(volt)I(Amp)2410R11kVvariable voltageFig.(1)5. Draw the relationship between V & I form table in question 4 thenexplain what does the slopes represent in V & I relationship?

In the given question; Color of first strip = orange So first digit = 3 Color of second strip =…

Answered: 2. Determine the value and calculate…

Engineering

Electrical Engineering

2. Determine the value and calculate the acceptable tolerance range the resistor that shown in the figure bellow: of

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Discussion: 1. Discuss your experiment results. 2. What are Positive and Negative biased clampers,…

A: Semiconductor devices are used nowadays very widely. They use silicon and germanium based devices.…

Q: 12V D1 R1 1k RRR D2

Q: A practical switch is operating at a switching frequency of 100 KHz and a 0.5 duty cycle. The switch…

A: A practical switch is operating at a switching frequency ofand a duly cycle.The switch is initially…

Q: what are two main advantages of using cermet in fixed resistors?

A: The Cermet film resistors are the film resistors comprised of an uncommon material called Cermet.…

Q: Temperature dependence of resistivity

Q: VOUT R1 + R2 VIN

Q: D1 D2 R1 5V 1K Determine the voltage across the resistor R1. (assume LED forward voltage is 2.1…

Q: Explain with reference to the components in the circuit and point P why the warning lamp is on when…

A: To Explain with reference to the components in the circuit and point P why the warning lamp is on…

Q: explain briefly and consicely the importance of tolerance in resistors

A: Tolerance of resistor is the nothing but how much is the resistance value measured of its actual…

Q: Tabulate the measurements. 4. Graph the tabulated results. C. Voltage-Current Characteristic Curve…

A: It is asked to show the V-I characteristics curve for reverse bias. Also ut is mentioned to…

Q: Determine the current at the resistor R1. (assume LED forward voltage is 2.1 volts and Diode forward…

A: In this question, We need to determine the current at the resistor R1. (assume LED forward…

Q: Determine the resistance and tolerance of each of the 4-band resistors shown below.

A: We need to find out the resistance value for the above two resistors.

Q: i) A linear potentiometer of 300 2 is used as sensor to sense linear displacement. For a…

A: consider the given question;

Q: c. Calculate the ripple of a capacitor filter for a peak rectified voltage of 30 V, capacitor C = 50…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: 1 use direct subfarction on the following binary numbers: ☺ lloo- lool

Q: Which one of the below device is not constructing by silicon a. Zener Diode O b. LED O c. Transistor…

A: Which one of the below device is not construction by silicon

Q: Identify the input and output of the thermistor. a. Voltage and temperature b. Voltage and…

A: The thermistor is a special type of resistor, where the resistance value is the function of…

Q: b. When the input is AC 110V @60Hz, Voltage output = 20V, Voltage ripple = 2V, and the maximum…

Q: Q. The input for any circuit at lab experiments are O B. the switches OD. None of the above O C.…

A: While performing the experiments in Laboratory, the inputs is given at one terminal and switches and…

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: need a reference about Elemental Semiconductor

A: Semiconductor has a electrical properties and which is used for the devices like diodes, transistors…

Q: Describe the function of voltmeter and ammeter

A: Voltmeter and ammeter is an instrument which are used in an electrical or electronic circuits. -The…

Q: electronics circuit determine the following: - If Q1 is turned on in Figure 4a, what is Vout?…

Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring…

A: In this question, we have to write about thermistor construction, resistance temp characteristics…

Q: What minimum value of series resistance s required when three 10-watt, 10-volt, 1000-mA zener diodes…

A: From the Question What minimum value of series resistance is required when three 10-watt, 10-volt,…

Q: Thermistor, which has high temperature coefficient of resistivity. is used as the sensing element in…

A: Right Answer option a. Solid-Semiconductor

Q: The resistance of a Thermal resistor or Temperature dependent resistor changed from 20 ohms to 22.5…

A: Find sensitivity

Q: The Voltage Drop will not depends upon the a. Length of the run O D. Voltage Drop Factor O c. The…

A: The formula for voltage drop In a line is, Voltage drop = current x impedance-----(1)

Q: Mention applications of a resistance strain gauge for measurement of non-electric quantities.

A: The applications of a resistance strain gauge for measurement of non-electric quantities are as…

Q: What is the minimum wire size for a 30 amp circuit?

A: To determine the minimum wire size for a 30 amp circuit. For the minimum wire size refer the NEC…

Q: R1 R2 VS RL D1 Z1 VS = 20,1 V, R1 = 11 k2, R2 = 11 kQ, %3D %3D %3D RL = 23,4 kn and Vzener = 9,6…

Q: 4. In the circuit below, calculate the load current, load voltage, load power, diode power, and…

Q: Define 5 applications where voltage regulators are used.

Q: Which of the following has higher energy? a. valance band electrons b. impurity atoms c.…

A: The above question is related to the subject of Electronics Devices To get the answer of the above…

Q: 3. For the circuit shown Figure 2, determine the range of the input voltage that will maintain the…

Q: In a semiconductor crystal, the atoms are held together by O Forces of repulsion O lonic bonds O…

A: In the semiconductor crystal, The atoms are together by sharing the electron pairs. And The bond…

Q: 11 R2 1K R1 D2 1K 5V D1 Determine the voltage across the resistor R2. (assume Zener voltage is 3…

Q: 3. WHAT IS THE RESISTANCE AND WHICH COLOR CODES ARE GREE (VALUE 10%) 4.DETERMINE THE RESISTANCE O…

A: The solution is given below

Q: A bank of nickel-cadmium cells is used as the emergency lighting supply for a hospital. There are…

A: When batteries or cells are connected in series, their voltages add and their current capacities…

Q: Q1.Three-phase half-wave controlled rectifier is shown in the figure below.Delivers 250W power with…

Q: * What minimum value of series resistance is required when three 10-watt, 10-volt, 1000- mA zener…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

2. Determine the value and calculate the acceptable tolerance range of
the resistor that shown in the figure bellow:
3. Record resistor colors based on its value for the following:
A. (9102 10%)
В. (6.8KО 20%)
4. Using the Multisim, connect the circuit shown in Fig. (1).
Increase the voltage as shown in the table and measure current in each step
then record it in table below:
V(volt)
I(Amp)
2
4
10
R1
1k
V
variable voltage
Fig.(1)
5. Draw the relationship between V & I form table in question 4 then
explain what does the slopes represent in V & I relationship?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the difference between mid point and full wave 3 phase rectifier? Name 3 devices that can replace thyristor in the circuit.
Explain clearly ...
Determine the voltage across R1. (Assume LED forward voltage is 2.1 volts and diode forward voltage is 0.7V)
vs=10v find vz and iz
At room temperature, what will be the value of thermal voltage? Show detailed calculations.
Make sure to indicate everything which needs to be indicated for an upvote. Thank you.
Q2: Define the component of Furnace temperature control system as a block diagram and the function of each unit
i. Draw a circuit diagram of potentiometer method with naming the components and derived the ratio of the two potentiometer readings. ii. In a measurement of resistance by potentiometer, the voltage drops across resistor under test and across 0.0252 standard resistors were found to be 0.882V and 1.2 V respectively. Determine the value of under test. iii. Write two advantages and disadvantages in Potentiometer method.
What minimum value of series resistance is required when three 10-watt, 10-volt, 1000-mA zener diodes are connected in series to obtain a 30-volt regulated output from a 45 volt d.c. power source ? R w E₁-45 V Eo= 30 V ↓
13 Determine the voltage at resistor R1. (assume Zener voltage is 4 volts and Diode forward voltage is 0.7V) * R2 1K R1 5V 1K D1 D2
The Voltmeter Ammeter method for measuring resistance is Select one: a. An appropriate method for measuring the resistance indirectly. b. An appropriate method for measuring the resistance directly. C. An appropriate less accuracy than direct resistance measuring methods.
BOX THE ANSWERS. ANSWER QUICKLY