2. By inspection, determine the zero-force members in the truss shown. Using method of members determine the force in member FH, GH and Gl. 1 12 kN D F 4 m B 6 kN 4 m -CE GIK 6 @ 3m

Q: What is Non-Dot Standard Specification?

A: Specification of Non-Dot Standard:

Q: A Elastic bar AB is connected to rigid member ACD as shown in the figure. Determine the displacement…

A: Given  Area , A= 200 mm2  Modulus of Elasticity, E= 80 Gpa

Q: own in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH…

A: To find the centroid-

Q: The Vicatronic

A:

Q: Draw the projections (Top, Front, Side) with Dimensions for this objects

A:

Q: What is Universal Transverse Mercator (UTM)?

A: A Universal Transverse Mercator is method to represent the three dimensional earth into two…

Q: Show the dimensions of the views shown.

A: The dimension of the given figure is shown below.

Q: 16 Constanta I Eeriodis Table A force Fof magnitude F making an angle e with the x axis is applied…

A:

Q: 6M WL 6

A:

Q: Differentiate between BIM and 3DModeling?

A:

Q: Picture attached

A: The strong acids and strong bases neutralize to form the neutral salts .The neutral slats have the…

Q: the beam shown in the figure, draw the influence lines for the reactions MA and RA and the shear and…

A: To draw ILD

Q: A 9-Storey building is supported by a steel braced frame on a certain location having the ff. data…

A:

Q: see the photo attached

A:

Q: A pre-stressed concrete T-beam of section shown is used over an effective span of 7m to support a…

A:

Q: ibute to compactive effort in pla

A:

Q: The surface area of a reservoir is 17.2 square miles and is underlain by impervious strata. In…

A:

Q: 4.1 The Architect as the Construction Manager (CM) is directly responsible to the Owner on all…

A: The role of the Architect as the Construction Manager (CM) is ensuring the successful execution of a…

Q: Where should you pay concentration when you are working with AutoCAD commands? Drawing area. Status…

A: Given data  Autocad commands  Tool bar Commands window  Status bar Drawing area

Q: SM Ø HOLES 10M A12.5M "SM 125M BOM FRONT VIEW SIDE VIEW

A:

Q: 1. Two new cast-iron pipes in series connect two reservoirs (Figure 1). Both pipes are 300 m long…

A:

Q: Problem 3. to ingrow A sheet asphalt mixture is made using the following percentages by weight of…

A: A sheet asphalt mixture is made using the following percentages by weight of the total…

Q: Determine the amount of total excavation in BCY needed for the spread footing shown below. A…

A: Before the construction of the footing, the excavation of the land is proceeding because the…

Q: top view drawing

A: In top view we see the object from top. Here dotted line represents a cut inside the object.

Q: (d) How long will consolidation settlement take for 50% consolidation to occur in the field if the…

A: Given Data: Coefficient of Consolidation= Cv=10 m2/year Depth of layer=3 m Drainage is two ways,…

Q: 3. A steel rod having a cross-sectional area of 450 mm² and a length of 185 m is suspended…

A: Self weight = 7850kg/m3= 3465.3825 N L = 185m A = 200mm2 E = 200GPa   It has been asked in the…

Q: If supports A and E in the given figure are constructed 30 ft and 2.3 in. apart instead of 30 ft…

A: Question is based on the frame supported on hinge support at both ends get deflected. Length of span…

Q: NORTH 28 -12- 2 -17'-5" 7'9" l'-8" 9'-8" 15'-5" 4* - 3 EAST 24 2 5'-5" 24'- 2'4" 2'-1" 12-5" T 28'…

A: Solution I have done three questions for you  The solution of the above question is following

Q: 50 Non-air entrained concrete Specimens: 150x300 mm cylinders Cement: Type I or Normal 40 28 days 30…

A:

Q: a Thirty dollars. b Twenty-five. c Fine. And you? d Hassan and Samir. e 'ma teacher. f The Times 8…

A: 1.What do you do? e. I'm a teacher 2.Who did you have lunch with?  d. Hassan and Samir 3.Where do…

Q: Describe what is Translational slides.

A: Translational slides:

Q: What exactly is computer-aided design (CAD)?

A: Computer aided design is main component of design of structures in Engineering.

Q: What does the drawing module provide?

A: drawing modules:

Q: A 1.5" high by 2" wide rectangular bar is attached to a channel section by 3/8" diameter mach screws…

A:

Q: answer the questions in the attached photo.

A:

Q: 4. Determine the force in members DF, DE and CE of the truss shown using method of joints. 200 N 300…

A: Given data:

Q: 1. A solid aluminum alloy disk with uniform thickness has an allowable speed of wall = 40,000 RPM, a…

A: Introduction- The neutral axis has the most shear stress. The shear stress decreases as the point…

Q: QUESTION 4 Find the area of the following shape. Area of the top horizontal rectangle is 27 cm2 and…

A: Top rectangle area = 27 cm²  Bottom rectangle area = 19cm²

Q: What is used to mark the tape lengths?

A: In surveying, tapes are used to measure distances that are level, vertical, or sloping. Tapes are…

Q: 1. An electric field of 8.50 x 105 V/m is desired between two parallel plates, each of area 35.0 cm2…

A:

Q: step by step procedure on doing this lab report (drawing/illustration) open compass traverse

A: Brief concept- Open compass traverse- A compass traverse is a technique for adding detail to a…

Q: Draw the influence lines for the reactions at supports A and C, the shear and moment at section B,…

A: Given data  Overhang beam Span length I will use Muller Breslau Principle to solve tgis question.

Q: 15.27 Two reservoirs having a difference of 40 ft in water elevations are connected by a 1.5-mile-…

A: Consider Case 1.   Head Loss=40 ft=12.192 mLength=1 mile=2414.02 mDiameter=0.3048 m

Q: For the figure shown, determine the average shearing stress in the bolt and the bearing stress at C…

A: For the given details,

Q: For the composite beam that is made of steel and aluminum as shown below, if we want to apply…

A: To convert one material to other, only width is modified as per width modification factor.

Q: 6) An experiment has been performed to determine the porosity of an unconsolidated sandpack…

A: An experiment was performed.Distilled water was poured into a graduated cylinder to a height The…