Balance the following set of latitudes and departures using the compass rule and give the results to the nearest 0.001 ft. Latitude Departure Side N S E W АВ 218.393 315.297 ВС 320.594 381.707 CD 315.253 184.161 DA 212.942 250.381 2.

Q: 8 ft 6 ft· 20 k D↓ -6 ft B 20 k -6 ft- E 15 k -6 ft- Case #1: Find ABy and ACx EA = constant E =…

A: Find: Vertical deflection at B and horizontal deflection at C

Q: 3.00 4.00 nswer to the nearest thousandth. 3.652 4.068 2.894 1.669 -2.00 1.00→→ $32. Determine the…

A:

Q: Define dilatometer test.

A: Dilatometer test is an in situ test method used to assess the strength and deformation of…

Q: For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x).…

A:

Q: 5. According to Fig. (a), (b), (c), specify what principle or relevant requirement is used on…

A: Dynamic tolerance diagram: Dynamic tolerance diagram 2 equal planes portray the volume of room used…

Q: Give details of JPCP, JRCP, and CRCP with necessary figures.

A: In pavement construction, three different concrete pavement design types are commonly used: Jointed…

Q: 32 3" fo=3000 ps fy= NWC = Mn=?, Tied bars. 28 = 60 ksi 多#9 14

A:

Q: A setup similar to the one shown in Figure 10.35 is commonly used to mea- sure the shear modulus, G.…

A: Given: The torque is 3450 N.m. The length of the specimen is 20 cm. The diameter of the specimen is…

Q: In Midpoint Method, a2 is equal to

A: From the given question, it is required to choose the correct option for the value of α2 according…

Q: 3m 2m Clay Sand 8 m Plan View || D₁. OB OB 4 m 4m 1 m 3m 2 4m AG=0 (1₁-1₂)2 I m = = 2²-1 늦쓸-5.5…

A: Given: Load, q = 400 kN/m2 Point A: Depth, ZA = 3-1 = 2 m

Q: Given Velocity= 50m/s discharge= 5 m/s O = 180° vehicle %3D VI neglect frictioons Find the frce…

A: Given Data: Velocity is v=50 m/s. Discharge is Q=5 m3/s. Angle θ=180°

Q: Complete the table below. LINE BEARING DIST (M) AB N 58° 46.9' E 38.588 BC S 57° 59.7' E 37.736 CD S…

A: Given :- Bearing and Distance of the five sided closed Traverse. To Determine :- Area of the…

Q: What should be the name of the layer shown as " purple ?" As a numerical calculation, the fault line…

A: We will solve this question in step no. 2

Q: In Compass traversing length of lines are measured by O a. Dumpy level O b. Theodolite O c. Chain O…

A:

Q: QC is part of the QM process, is primarily concerned with process control during construction, and…

A: Solution:  The correct option to above question is option A

Q: A 4.020-gram bullet is projected horizontally to a block of timber that rest on a horizontal floor.…

A: Given mass of the bullet  m=4.02 gmbullet is projected horizontallylet the initial speed of the…

Q: 7. For an unknown reason, an adventurous man with a height of 1.95m is holding an open cylindrical…

A:

Q: he d n or er if n or er if n e al d P2.10. Refer to Figure P2.9 for the floor plan. Calculate the…

A:

Q: Convert the following Reduced Bearings into WCB. • N 65° E • 439 15' E S 52º 33' W •N 32º 42' W

A:

Q: diagram. 10kN.m 2m 3m (20+#ID)/2 KN 2m 5m 77 5kN/m B

A:

Q: Describe the Effect of Groundwater Table.

A: Ground water is considered as one of the most valuable resources of water. It has great significance…

Q: Lim x25X+ 2 2X+ 2X-1 .3 メ→。

A: To evaluate: limx→∞x2-5x+22x3+2x-1

Q: Design the most efficient, rectangular, concrete (n=0.015) channel to carry a flow of 2,500-ft³/sec,…

A:

Q: Construction cost of the manufacturing plant is considered as overhead cost. True False

A: Explanation :  The construction cost of the manufacturing plant includes direct and indirect costs…

Q: Show step by step solution

A: FINAL ANSWER:-       Therefore,the minimum coefficient of friction is 0.2167.Explanation:

Q: Calculate the following: e. D75, a. D10 b. D25 c. D30, f. Cu, g. Cc, h. So d. D60'

A: Sieve   Mass  % Cumulative % Cumulative % No Sieve size Retained mass Retained Retained   #4…

Q: What is Uniformly loaded strip ?

A: Answer:- Uniformly loaded strip: A uniformly loaded strip is defined as that strip which is…

Q: abel an earth dam

A: The successive layers of earth when piled together to form core and the upstream and downstream…

Q: (3) 12 12" 12 4" 30" Uncra e ked ft-k M=50 ftop = ? fbot = ? Mer= ?

A:

Q: What are the values of Q1, Q2, and Q3?

A:

Q: Given the following: b=380mm d=530mm fc'=30MPA fy=320MPa Mu=650KN-m Determine As A. USE NSCP 2015,…

A: Given,

Q: Calculate the following: a. D10 b. D25 c. D30 d. D60 e. D75. f. Cu, g. Ce,

A:

Q: Calculate the total area required for placing the quarry tiles on the internal walls in this…

A: There are two short walls and two long walls, And there is a deduction in area in the place of the…

Q: One side of a regular octagon is "e". Find the area of the region inside the octagon. O 4.8e2. sq.…

A:

Q: Please show detailed solution.

A:

Q: @ * 30" 16" 14" 16" 6" Uncracked. M = 60 (1) ftop ?? (2) f bottom=? ft-k

A:

Q: Yt (sn + G, (1-n)) Yw

A:

Q: Question #10 Determine the centerline length (wall is 300 mm thick)

A:

Q: A ball is thrown vertically upward with a velocity of 80ft/s. Two seconds later a second ball is…

A: