2. As shown in the figure, a round viewing window with a diameter of 0.90m in a large tank of seawater (sg=1.03). The top of the window is 1.50m below the liquid surface, and the window is angled 60 degrees respect to the horizontal. Determine the hydrostatic force acting on the window and the location of the center of pressure measure vertically from the water surface. SEA WATER 1-50 W 06 0

2. As shown in the figure, a round viewing window with a diameter of 0.90m in a large tank of seawater (sg=1.03). The top of the window is 1.50m below the liquid surface, and the window is angled 60 degrees respect to the horizontal. Determine the hydrostatic force acting on the window and the location of the center of pressure measure vertically from the water surface. SEA WATER 1-50 W 06 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a horizontal pipe with a cross-sectional area of 5m^2 at a speed of 6L/sec. With a pressure of 3atm at point A. At point b, The cross-sectional are is 3m^2a) what is the speed of the water at point b.b) calculate the pressure at point b.
(Buoyancy, force on plane surface) A cube, 4.9 ft on a side, weighs 2900 lb and floats half-submerged in an open tank as shown in the figure below. For a liquid depth of 10.4 ft, determine (a) the magnitude and (b) the location of the force of the liquid on the inclined section AB of the tank wall. The width of the wall is 7.2 ft. Show the magnitude, direction, and location of the force on a sketch. 10.4 ft (a) FR = (b) YR = 4.9 ft Liquid Cube V Wall width=7.2 ft 26° lb on centerline ft along wall from free surface
Water at 20°C flows through an inclined circular conduit as shown. The conduit is inclined at an angle of 0 = 40 ° and undergoes a contraction from a larger to a smaller diameter. The diameters upstream and downstream of the contraction are D= |20 mm and d = 60 mm respectively. Pressure gages are installed near the entrance and exit of the contraction as shown, separated by a distance of L = 1.9 m. A differential manometer is also installed with ends at the same sections as the pressure gages. The manometer fluid has specific gravity of 13.6. pressure gages h flow differential manometer Q Tap image to zoom
Sea water h 60⁰ Window PROBLEM 3.58 As shown, a round viewing window of diameter D = 0.8 m is situated in a large tank of seawater(S = 1.03). The top of the window is 1.2 m below the water surface, and the window is angled at 60° with respect to the horizontal. Find the hydrostatic force acting on the window and locate the corresponding CP.
Two clean, parallel glass plates, separated by a distance d=1.5mm, are dipped in a bath of water. How far does the water rise due to capillary action if surface tension is 0.0730N/m? Use 9.81m/s? as unit weight of water O 9.92 mm O 54.17 mm O 12.16 mm O 19.84 mm
Consider a system where a horizontal, laminar, separated flow of air and water at 100 kPa pressure and 20 C temperature are moving between two infinitely-sized parallel plates. The water flow is not forced, but is carried along by the air flow. The 'superficial velocity' of the air is 0.1 m/s (superficial velocity is volume flow rate / flow area, representing the average velocity of the flow). The depth of the water film is 2 mm and the thickness of the air layer is 5 mm. Use the multiphase balance equations and interfacial boundary conditions to derive the velocity profile in the air and water, with y=D0 being the interface between the two.
Question 4. The L-shaped cap in the figure is hinged from point A. Neglecting the weight of the lid, a) Before opening the lid counterclockwise, determine the maximum water height H in symbols. b) If w=4 m (width of the cover perpendicular to the plane of the paper), B=5.77 m and d=6 m, determine the numerical value of H. C) Find the horizontal and vertical components of the hydrostatic force and the resultant force direction with the values given in b B articulation A H
(Buoyancy, force on plane surface) A cube, 4.4 ft on a side, weighs 3110 lb and floats half- submerged in an open tank as shown in the figure below. For a liquid depth of 10.6 ft, determine (a) the magnitude and (b) the location of the force of the liquid on the inclined section AB of the tank wall. The width of the wall is 8.1 ft. Show the magnitude, direction, and location of the force on a sketch. 10.6 ft 4.4 ft Liquid (a) FR = centerline b) YR= all from free surface Cube A V Wall width 28° lb on ft along