2. An equilateral triangle pipe, as shown in the figure has a uniform thickness of 1.5 mm. The length of the pipe is 2.0 m, and the value of maximum shearing stress is 50 MPa. If G = 30 GPa, determine: a. The value of torque b. The value of angle of twist

Q: own in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH…

A: To find the centroid-

Q: Draw a figure of door and label it

A: The figure and door is in next step

Q: assembly drawing, all parts are drawn in their working position with a completed dimension. s are In…

A: Option c ( detail ) is correct.

Q: Describe Fellenius Method.

A: In situations where the effective angle of shearing resistance over the failure surface is not…

Q: Define stirrup

A: Stirrup: A stirrup is a closed loop of reinforcement(steel bar) in a beam. It is called as tie-bar…

Q: 3 cm 7 cm 5 cm 5 cM Detenmine the Folloeing %3D

A: Calculation of area and moment of inertia

Q: How are forces between the tape and strips similar to those of magnetism?

A: The forces between a strip of adhesive tape and a surface are primarily due to intermolecular forces…

Q: Determine the number of metal studs need to construct 128 feet of interior walls, with 6 corners, 12…

A: ANS-1) Given- corner=6 intersections=12no of 3-foot wide doorways=5Studs spacing= 16 inches or 1.33…

Q: Q4: Prove that:

A:

Q: Define scour

A: Scour is the removal by hydrodynamic forces of granular bed material in the vicinity of coastal…

Q: Describe about the Sliding Block Analysis.

A: The sliding block analysis method used by the Newmark is an engineering which determines permanent…

Q: Find the slab thickness for the pand shown Column size - 300*300 -5.00- Jy 350 Mpa -009- 2-5

A: The column size = 300300The yield stress (fy) = 350 MPaTo determine:-The slab thickness

Q: 10- What is the BOM and how is it arranged on a format?

A: Note : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: Find the centroid of given composite figure. Set- up the reference axis on the lower left corner.…

A: Centroid about x-coordinate :x¯=A1x1+A2x2+A3x3A1+A2+A3

Q: Problem 1 Wind blows on the side of a fully enclosed agricultural building located on an open flat…

A: When wind engineering is used to analyse tall buildings, the major load is frequently found to be…

Q: Define metamorphic.

A: Metamorphic:

Q: What is Dimensional Lumber often used for in construction projects?

A: Dimensional lumber is a wood lumber that is cut to pre defined standard sizes These are structural…

Q: A composite beam is fabricated by bolting two 2.5- in.-wide by 11-in.-deep timber planks to the…

A: Es = 30800 ksi Et = 1660 ksi Determine a. Maximum bending stress in timber and steel if P = 3.5…

Q: Bb Course Mail- myct/itemView?assignment ProblemID=15609916&offset=next Max FBC = As shown, a truss…

A: Find the force in member BC by method of sections

Q: draw a structural base in a picture

A: Structural layout shows the structural components of a building like beams & colums. This layout…

Q: Complete an interpretation drawing that show permissible surface condition that lies partiall part…

A: The permissible surface condition is as follows. When a tangent modifier is added it only controls…

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: B) What is the difference between Spaced Sheeting and Close Sheeting

A: Solution: Closed sheeting is defined as the continuous frame having vertical and horizontal…

Q: Define spudding

A: For drilling a well in a gas and oil industry, this process is used at the beginning.

Q: A & C are incorrect, please re-work

A: As per question , I solve here only a and c. Find out - (a) Radius of curve  (c) Tangent length

Q: hey! good work, very neat and organized. However, the value of X for section D is incorrect. Maybe…

A:

Q: Method of joints. AB, BD, BC

A: To find force in member AB,BD,BC

Q: Draw and name the different Types of Trusses

A: Truss is a structure commonly used in case of bridge spans. Members carry load because of the…

Q: Draw the front, Side and top

A: For this, we can draw the diagram in Autocad. I have used the same to draw the diagram and have…

Q: make a short report to stone

A: Stones or rock is a natural substance that is mined and quarried from the earth and used widely in…

Q: What are the Automated 3D truss/steel structure on-site assembly

A: Concept- On-site assembly- The management and completion of all project operations used to deliver…

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

A:

Q: A CPLD is based on

A: A CPLD- Complex Programmable logic device It is a programmable device based on complexity PALs and…

Q: The steel connection below shows a beam W310 x 52 connected to column W310 x 74 using 2 Web Plates…

A: CAD Template 1st;

Q: How are finished grades determined in machine guidance and control?

A: .Today’s machine-control systems help operators of all skill levels get to finished grade faster by…

Q: Which shortcut key lets you rotate the drawing area? RO О тв O z O L

A:

Q: Search and draw other types of CONCRETE BLOCK (at least 8 types). -name of concrete block -usage -…

A: Name of the concrete blocks Usage  Size image  1. Solid Concrete Block  Used in load bearing walls…

Q: All are incorrect, can you re-work?

A: The degree of the curve = Da = 5°0' The intersection angle = 20°30' The station of the PI = 63+25.53…

Q: Consider the beam X-section shown. Assume 1 inch clear spacing between two layers of bars. As the…

A: 1 inch clear spacing spacing between two layers of bars. Beam width = 12 inch Layer = 2 No of bars =…

Q: What is the actual size of a 200 mm concrete block? Select one: O a. 190 mm O b. 210 mm O c. 150 mm…

A: To Determine :- Which one of the option given is correct.

Q: Calculate the second moment of area for a 50 mm ×100 mm stud with the actual dimensions shown on…

A: Given:- The dimension of the stud = 50 mm × 100 mm  The actual dimension of the stud = 45 mm × 105…

Q: Differentiate half sectioning & full sectioning

A: Full  Sectioning  Half Sectioning  1. It is the full section view. 1. It is the half section view.…

Q: Define struts.

A: Struts:- They are long, slender structural members in an assembly which are subjected to the only…

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.