2. An engine working on Otto-cycle receives 1500 k/kg amount of heat. The pressure and temperature at the beginning of compression is 150 kPa and 300 K, respectively. The compression ratio of the cyde is 8.0. Determine: (a) The work net, in k/kg (b) The thermal efficiency of the cycle (c) The mean effective pressure, in kPa (d) The maximum temperature in the cycle, in K

2. An engine working on Otto-cycle receives 1500 k/kg amount of heat. The pressure and temperature at the beginning of compression is 150 kPa and 300 K, respectively. The compression ratio of the cyde is 8.0. Determine: (a) The work net, in k/kg (b) The thermal efficiency of the cycle (c) The mean effective pressure, in kPa (d) The maximum temperature in the cycle, in K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An gas flows through a uniform diameter pipe whose outlet point is higher than the inlet point. Assuming that the system is steady state with constant temperature and an outlet pressure less than the inlet pressure, how does the outlet kinetic energy compares with the inlet kinetic energy? insufficient information b. the same c. lesser d. greater
Thermodynamics
Given a ttt diagram of steel 1040. For each section determine the final steel structure. Mark the tracks on the graph. For your convenience, 2 identical graphs are attached below. Each section starts from a temperature of 800c: 1 Rapid cooling to 400c, staying for 100 seconds at this temperature and then rapid cooling to room temperature. 2. Rapid cooling to 600c, staying for 30 seconds at this temperature and then rapid cooling to room temperature. 3. Rapid cooling to 400c, staying for one second at this temperature and then rapid cooling to room temperature. 4. Rapid cooling to 700c Stay for 8 minutes at this temperature and then rapid cooling to room temperature.
STEAM PROCESSES
Note:- • Do not provide handwritten solution. Maintain accuracy and quality in your answer. Take care of plagiarism. • Answer completely. • You will get up vote for sure.
pls answer correctly this is my last attempt thanks
5.5
Thermodynamics: Please show step by step solution for the following Practice problem
) Two boilers, one with superheater(B1) and other without superheater(B2) are delivering equal quantities of steam into a common main. The pressure in the boiler and main is 20 bars. The temperature of the steam from a boiler with a superheater is 350oC and temperature of the steam in the main is 250oC. The steam in B2 is wet steam at 20oC. i) Draw a sketch of the problem with all thermodynamic properties from steam table shown on the sketch. ii) Determine the quantity of steam supplied by the other boiler. Take the heat capacity of steam, Cps = 2.25KJ/Kg.hgas= hg + Cps (Tsap-Tsat)
5.7 In a continuous agitation heating tank, w=wi=200lb/min, Cp and density are constant, the volume of the heating tank V=1.63ft^3, the specific heat of the liquid is 0.32Btu/(lbF), and the density is 62.4lb/ft^3 am. The heat input Q from the heater is 1680 Btu/min, and the inflow temperature is maintained at 80F. (a) Find the response when the inlet temperature suddenly decreases to 65F.
FInd the QUESTION 4 The following processes occurs in a reversible thermodynamic cycle 12 Reversible polytropic compression at pressure 0 8 bar at volume 0 07 m³ to a pressure 11 bar and specific volume 0 6 m/kg The index of compression may be taken as n 2-3 Reversibly expansion with expansion index of 2 to pressure 2 3 bar 31 Reversible cooling at constant volume to the initial state Calculate the mass of fluid present to 3 decimal places QUESTION 5 The followin
Please provide solutions and mollier diagram plot for review, TYSM!