2. A truck is traveling along the horizontal circular curve of radius r= 60 m with a speed of 20 m/s which is increasing at 3 m/s?. Determine the truck's radial and transverse components of acceleration.

Q: Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L = 3.2…

A: For calculating the acceleration of block B , first the velocity is calculated using  VB = dx/dt…

Q: Collars A and B slide along the fixed right-angle rods and are connected by a cord of length L = 7.1…

A: Data given-  L = 7.1 m  y = 2.8 m  vA = 2.42 m/s

Q: A car with tires of 700 mm diameteraccelerates at a constant rate from rest to a elcoity of 68 km/h…

A:

Q: The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a…

A:

Q: For the problem related to Fundamental.3, a sketch of both vehicles showing their respective…

A:

Q: А A EAG IB B C -IP'

A: Given system,

Q: Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. The car has a forward…

A: (a) To find: The velocity v of the car when point P at the tire has zero horizontal component of…

Q: A chute delivering shipments of freight is so designed that the boxes starting from rest, receive a…

A:

Q: Question 1: (A): Pulleys A and B have diameters of 100mm and 200mm, respectively. As the tape speed…

A:

Q: 2 Under the action of force P, the constant accelera- tion of block B is 3 m/s² to the right. At the…

A:

Q: In fixed-axis rotational motion, the normal component of acceleration at the body's center of…

A: When a body is in rotational motion about any fixed axis every particle on the body performs…

Q: roblem 2/ Particle P moves along the curved path shown. At the instant represented, r = 2.0 m, e =…

A:

Q: The car is traveling at a speed of 71 mi/hr as it approaches point A. Beginning at A, the car…

A:

Q: A test car starts from rest on a horizontal circular track of 95-m radius and increases its speed at…

A: To Find : The magnitude of the total acceleration of the car after 15 second. Given : The radius of…

Q: When the mechanism is in the position shown, the velocity of the sliding collar is VA = 1.6 m/s, and…

A: Data given-

Q: A marbľe M is constrained to move in the horizontal plane along a wire whose shape is as…

A: Va = 5 m/s ra = 2 m Vb = 3 m/s || aB || =10 m/s2  Tangential at B = ab,t = 2 m/s2  To find:  Marbles…

Q: (+) y-axis A car initially at rest, is traversing a circular track in clockwise rotation. If it's…

A: B=60 ft/s2

Q: For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the…

A:

Q: A car is traveling around a circular track of 760-ft radius. If the magnitude of its total…

A:

Q: Initially the blades of a two-blade horizontal axis wind turbine are turning at angular velocity of…

A: The objective of this question is to determine the distance travelled by point P at the tip of the…

Q: Determine the r- and θ-components of velocity and acceleration. Answers: vr =  in./sec vθ =…

A:

Q: At the shown instant the roller C is moving up the slot with the constant speed of 1.2 m/s. For the…

A: Given: VC=01.2 m/s

Q: Dynamics In the system presented, the tractor ? is used to hoist bale B with the pulley mechanism.…

A:

Q: A test car starts from rest on a horizontal circular track of 95-m radius and increases its speed at…

A:

Q: A basketball hits the ground and bounces with velocity VA and an angle theta from the vertical, such…

A:

Q: At a given instance of time, a train engineer sitting in the engine car at E reportsa speed along…

A:

Q: Question No. 2. The point at A the total acceleration of airplane is 3g. If airspeed is 800 km/h and…

A: Given data  total acceleration at A (a) = 3g =3*9.81 = 29.43 m/s2 airspeed (v) = 800 km/hr…

Q: The particle P starts from rest at point A at time t = 0 and changes its speed thereafter at a…

A: Given Data The acceleration at which the speed changes is: a=1.2g The time given is: t=0.98 s The…

Q: 1. A platform is rotating about the vertical axis such that at any instant its angular position is 0…

A: Position is r=0.1t3=0.11.53=0.3375 m By differentiating the above relation θ˙=dθ˙dt=6t12 rad/s By…

Q: An experimental vehicle A travels with constant speed v relative to the earth along a north–south…

A: Given Data  Vehicle speed, V=500 Km/hr=138.88 m/s

Q: .13 A A = 70 km/h. At the 90 km/h, and it is dec

A: vA=70km/hvB=90km/hDecreasing at rate =1.8m/s2To-Find:-Relative acceleration vector

Q: A disk of radius R = 0.5833 ft spins at a constant angular speed of o = 52.36 rad/s in the clockwise…

A:

Q: A new discovered asteroid were observed by astrophysicist. It is said to be moving along a circular…

A: The asteroid is moving in circular motion so some pertaining relations are dθdt=ω, d2θdt2=dωdt=α…

Q: The air transport B is flying with a constant speed of 445 mi/hr in a horizontal arc of 9.1-mi…

A: To Find : The acceleration of A as measured by an observer in and turning with B. Given : The speed…

Q: A car travels along the circular curve of radius r = 294 ft. At the instant shown, its angular rate…

A:

Q: A toboggan is traveling down along a curve which can be approximated by the parabola y = 0.012².…

A:

Q: Cable at point b is pulled downward at 4 ft/s and decreasing at a rate of 2 ft/s.   WHAT IS THE…

A: Given Velocity at B = 4 ft/s Deceleration = 2 ft/s2 To find Magnitude of velocity A Direction of…

Q: 2. The satellite dish below tracks the of Determine movement airplane an straight line traveling…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.