2. A suitcase slides down a ramp between Points A and B as shown below. It has an initial velocity of 2 m/s and a mass of 2.1 kg. The coefficient of static friction between the suitcase and ramp is 0.3 while the coefficient of kinetic friction between the suitcase and ramp is 0.2. Answer the following questions. a. To analyze the suitcase using Newton's 2nd Law of Motion, do you need to know the weight, the mass, or both? Justify your response. 2.7 m b. Do you need to use static friction, kinetic friction, or both in this analysis? Justify your response. c. Draw and label a free-body diagram (using S.P.R.E.A.D.) and a kinetic diagram of the suitcase. Hint: There is an advantage to rotating your x-axis to be along the surface of the ramp. Do not label the figure provided. d. What is the friction force acting on the suitcase as it slides down the ramp? Show your work.

2. A suitcase slides down a ramp between Points A and B as shown below. It has an initial velocity of 2 m/s and a mass of 2.1 kg. The coefficient of static friction between the suitcase and ramp is 0.3 while the coefficient of kinetic friction between the suitcase and ramp is 0.2. Answer the following questions. a. To analyze the suitcase using Newton's 2nd Law of Motion, do you need to know the weight, the mass, or both? Justify your response. 2.7 m b. Do you need to use static friction, kinetic friction, or both in this analysis? Justify your response. c. Draw and label a free-body diagram (using S.P.R.E.A.D.) and a kinetic diagram of the suitcase. Hint: There is an advantage to rotating your x-axis to be along the surface of the ramp. Do not label the figure provided. d. What is the friction force acting on the suitcase as it slides down the ramp? Show your work.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can this be done using simpsons rule?
Give a steps by steps answer of the solution
I need solve this in quickly time please please
Handwriting not allow please And give me complete answer
Solidification is the process of changing the state of the material from .. powder to solid liquid to solid. solid to liquid. solid to solid none of the above 00O o
The Figure to the right shows a manufacturing process? What is this process called? 2. Identify the parte from 1 to 8 3. Explain how this process is performed? 1.
Hello, I was just wondering how you find hte angle of the blocks to 45 degrees? Thank you!
What are the concentrated forces?
thank you can u plz solve f&g now
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
Find warrk done
Can I have the formula for the percent difference?