2. A steam-jet pump maintains a temperature 50°C in the evaporator. The cooled water leaves at the same temperature and warms to 10°C as it does its refrigeration. Make up water is available at 21°C. There is required 1.27 kg of nozzle steam per kg of vapour removed from the evaporator. For a 175 kW plant, compute the, a.) Quantity of chilled water b.) Volume of vapour handled c.) Quantity of steam needed.

2. A steam-jet pump maintains a temperature 50°C in the evaporator. The cooled water leaves at the same temperature and warms to 10°C as it does its refrigeration. Make up water is available at 21°C. There is required 1.27 kg of nozzle steam per kg of vapour removed from the evaporator. For a 175 kW plant, compute the, a.) Quantity of chilled water b.) Volume of vapour handled c.) Quantity of steam needed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

write in hand written
there is an update in the previous question - A Carnot refrigeration cycle absorbs heat at 250 K and rejects it at 300 K Calculate- i) the coefficient of performance of this refrigeration cycle. ii) If the cycle is absorbing 1130 kJ/min at 250 K. how many kJ of work is required per second iii) If the Carnot heat pump operates between the same temperatures as the above refrigeration cycle, what is the coefficient of performance ?
An ammonia simple saturation cycle operates at 35 psia suction pressure and 172 psia condenser pressure. For a load of 1600 Btu per minute, determine: a) The refrigerating effect b) The COP c) The gallons per minute ( GPM ) of cooling water in the condenser if water temperature is increased by 10 F. d) The actual work e) The actual piston displacement with 5% clearance.
A heat exchanger has the objective of condensing 5 kg/s of water vapor and taking it from a pressure of 1.0 MPa and 300 °C to atmospheric pressure and 60 °C. Liquid water is used as refrigerant (Cp= 4.22 kJ/kgK), it enters at 1 °C and leaves the exchanger at 50 °C. a) What is the mass flow rate of the cold water stream? b) If the water is exchanged for another refrigerant substance whose specific heat is 2.0 kJ/kgK, what will be its outlet temperature if the same mass flow is maintained?
There is a steam power cycle that uses water as the working fluid, where the condenser pressure is 20 kPa. The pressure in the boiler is 4 MPa. The steam that comes out of the boiler is saturated steam. The water enters the pump as a saturated liquid.The isentropic efficiencies of the pump and turbine are 87% and 97% respectively. Determine a) Real work on the pump b) Heat transfer in theboiler c) The real work on the turbine d) The heat in the condenser e) The thermal efficiency of the cycle
The air entering the turbine with 1200 K and 1200 kPa expands to 100 kPa pressure in two stages. When the air is reintroduced to 1200 K at a constant reheat pressure of 350 kPa and both expansion stages are ideally realized: a) Total expansion work (kJ/kg) b) Intermediate heating amount (kJ/kg) c) Calculate the rate of increase in work according to the stepless (without reheating) expansion. Features for air: k=1,4, R=0,287 Jkg K,F1,005 klkg K k = 1.4 R = 0.287 kJ/kgK Cp = 1.005 kJ/kgK %3D
I need the answer as soon as possible
Refrigerant 134a is used in a cooling system operating according to the ideal cooling cycle with vapor compression for cooling the cold storage in the milk processing plant. The flow rate of the refrigerant is 0.10 kg/s. The condenser and evaporator pressures are 1000 kPa and 600 kPa, respectively. a) Calculate the cooling capacity as (kW). b) Calculate the volumetric flow rate of the refrigerant at the compressor inlet. c) Calculate the efficiency coefficient of the cooling system.
Consider an ideal Brayton refrigeration cycle with a regenerative heat exchanger. Six kg/s of air enters the compressor at 100 kPa, 300 K. The compressor pressure ratio is 3.75. The compressed air enters the regenerative heat exchanger at 350 K and is cooled to 320 K before entering the turbine. a) Calculate T4 b)The net power input kW c)The refrigeration capacity in kW d) The coefficient of performance
A refrigeration system with a capacity of 10 tons of refrigeration, operates at 210 kPa in the evaporator, while in the condenser it is 850 kPa. If R-134a refrigerant is in a saturated state, calculate the theoretical power required to operate the compressor. Compressor power = ... W.
1- Consider two vapor compression refrigeration cycles .The refrigerant enters the hrottling valve as a saturated liquid at.30°C in one cycle and as subcooled liquid at 30°C n the öther one. Tlhe evaporátor pressure for both cycles is the same .Which cycle do you jink will have a higher COP ?
Answer this ASAP,thx In a steam turbine, saturated steam enters the turbine at a pressure of 16 MPa and a pressure in the condenser of 8 kPa. The mass flow rate of the fluid entering the turbine is 100 kg/s. calculate: A) the power produced B) the rate of heat transferred to the steam passing through the boiler C) the thermal efficiency