2. A sight is taken with an engineer’s level at rod held 80 m away and the reading was observed to be 2.81. The bubble is then leveled through five spaces on the level tube and the reading increased to 2.874 m. What is the radius of curvature of the level tube if each division is 0.6 mm?

Q: Using an engineer's level, the reading on a rod 80 m away was observed to be 2.84 m. The bubble was…

A:

Q: Situation XVI A concrete spillway with permanent crest at elevation 303m controls a reservo 11.50…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Water flows at a depth of 1.4 ft with an average velocity of 20 ft/s in a wide rectangular channel.…

A:

Q: 0.8m (1) Find P&Y (4 AND B 3ku 1,2 M 2M 11.AM YJ ( -0.tm 1.5M G-- D 3 KN 1.2m

A: Calculate the value of P and Y??

Q: 1. Water is to be delivered from a reservoir through a pipe to a lower level and discharged into the…

A:

Q: What are the benefits and drawbacks of beginning a project using a pre-built model vs a clean sheet…

A: Benefits of Beginning a Project with a Pre-Built Model: 1. Cost Savings: Using a pre-built model can…

Q: With the use of an engineer's level, the reading from a rod was recorded as 2.50m when the rod was…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: SITUATION 8: A trapezoidal channel discharging 20.40 m³/sec at a depth of 1.2m and a base width of…

A:

Q: A water tank has a leak at the bottom due to an orifice. The orifice cause the water surface to drop…

A:

Q: Al C 2.5 m 20 KN/m 7.5 m B

A:

Q: A rod is 60 m away from the instrument and the rod reading is 2.24 m. The bubble on the level tube…

A:

Q: Q1 /Complete (HI. method ):- compute level points( tp1, tp2, BM2 ) BS FS Elevation HI Point 100.00…

A: point BS H.I. FS Elevation BM1 12.64 112.64   100.00 TP1 10.88 120.41 3.11 109.53 TP2 9.72…

Q: . Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014.  a.)…

A:

Q: Calculate the diameter of vertical pipe needed for flow of liquid at R = 1800 when the pressure…

A: Consider the given data

Q: Find the discharge over a triangular notch of angle 60° when the head over the V-notch is 0.5m.…

A: given- Angle of notch θ=60ohead H=0.5 mCd=0.65

Q: A 3 m B 4 kN/m 3 m-

A: TO FIND   REACTIONS

Q: * In levelling operation If second reading is more than first, it represents a rise If first reading…

A: In levelling operation both 2 and 3

Q: 19. What is the vertical reaction at A in KN? a) 475 20. What is the reaction at B in KN? a) 475 b)…

A:

Q: a 100mm height cylinder with specific weight of 5kn/m^3 is submerged ina a a fresh water with…

A:

Q: 417. For a flowrate of 2 m'is of air (y = 12.0 N/m) what is the largest A that will cause water to…

A: step 1-

Q: EL (H7-3) 4 y,y2 = power loss due to jump in rectangular channel can be estimated by the following…

A: ρ symbol used here to indicate the density of fluid.

Q: For a given circular channel, D = 3m, n 0.016 and slope 0.2°, determine the maximum velocity in m/s.…

A:

Q: Problem no. 2. Compute MD 1m 15 kN/m 4.2m B 5m 6m 3m 6 kN/m

A: Given: A simply supported beam  Required: Moment diagram

Q: exact answer. 2.43

A:

Q: Q5 What is the size of a Steel sewer pipe that flows 30% full a slope of 0.003 with ((d=.... at a…

A: Draw FBD:

Q: Atube15mlongistoconnecttwolargetankswhosedifference in water level is 2m. The tube is to carry 5L/s…

A: Given: The length of the tube is 15 m. The head loss is 2 m. The flow rate is 5 L/sec.

Q: Air Air 0.4m 0.4m Oil S3. 09 0.5m Water

A: Given h1= 0.4 m ,h2= 0.4 m , h3 = 0.5 m  Density of water= 1000 kg / m3  density of oil = 900 kg/m3…

Q: A mine orientation survey is to be done using two mechanical plumb-lines in one vertical shaft. The…

A: A mine orientation survey is to be done using two mechanical plumb-lines in one vertical shaft. The…

Q: For the given Differential Level notes below Station BS HI FS Elevation BM-125 2.38 897.39 ТР-1 3.11…

A:

Q: A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3…

A: Initial rod reading =2.3 metersFinal rod reading = 1.8 metersNumber of spaces moved by the bubble on…

Q: Compute the critical effective area between staggered failure paths for the channel bar shown if the…

A:

Q: A pipe system is using a lake as water source at elevation Om. The water is supplied in a reservoir…

A:

Q: * In levelling operation If second reading is more than first, it represents a rise If first reading…

A: In surveying levelling is done to measure the elevation of different points or survey line on the…

Q: Find the corrected level for point (A) if you know that the true level of (A) is 30 m according to…

A: Solution: Given Data: The true level of A=30 m Backsight reading=1.782 m Foresight reading=1.365 m…

Q: Q2/ Arwana canal with rectangular cross section. The wall of the channel (4-2) has a water depth of…

A: Given Data: The discharge of water from the canal is Q=360 m3/2 min=3 m3/s. The water depth is…

Q: 10 kN 50 kN - m C -B 2m- 3 m

A:

Q: 8m Sm 11m 1m

A:

Q: A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3…

A: Given data,distance=D=200minitial reading of 2.3 metersnumber of division=n=7final reading=1.7length…

Q: corrected level for point (A)

A:

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.