2. A load of 140,000N is applied to a cylindrical specimen of a steel alloy displaying a stress-strain behavior shown in Figure 5.10 that has a cross sectional diameter of 10 mm. a. Will the specimen experience elastic or plastic deformation? Why? b. If the original specimen length is 500 mm, how much will it increase in length when this load is applied?

2. A load of 140,000N is applied to a cylindrical specimen of a steel alloy displaying a stress-strain behavior shown in Figure 5.10 that has a cross sectional diameter of 10 mm. a. Will the specimen experience elastic or plastic deformation? Why? b. If the original specimen length is 500 mm, how much will it increase in length when this load is applied?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tensile specimen of cylindrical brass cartridge subjected to a load of 350 kg has a cross section diameter of 3.5 mm and a gage length of 25 mm. Calculate the Young's modulus and engineering strain that occurred during a test if the distance between gage markings is 26.5 mm after the test.
What is plane strain condition? List all zero stress and strain components in plane strain.
Draw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking region
How does the increase in the temperature affect the Youngs modulus, UTS and ductility of material? (At the same strain rate).
A ductile specimen that has an initial length of 10 cm is tested under uniaxial loading. If the test is under tension and the nominal strain is 21.9%, please calculate the true strain in %.
EXAMPLE 3.9 Finite-element²¹ analysis shows that a long structural component car- ries a uniform axial stress of 35 MPa (T) (Figure 3.29). A hole in the center needs to be drilled for passing cables through the structural component. The yield stress of the material is 200 MPa. If failure due to yielding is to be avoided, determine the maximum diameter of the hole that can be drilled using a factor of safety of 1.6. 10 mm H = 100 mm -d- Figure 3.29 Component geometry in Example 3.9.
4. For a brass alloy, the stress at which plastic deformation begins is 345 MPa and the modulus of elasticity is 103 GPa. What is the maximum load that may be applied to a specimen with a cross-sectional area of 130 mm² without plastic deformation? b. If the original specimen length is 76 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
QUESTION 7 Which governing equations are required to solve a plane elasticity problem? Boundary conditions Equilibrium condition and boundary conditions Equilibrium conditions, boundary conditions, and the compatibility equation QUESTION 8 Which of the following conditions must a structure meet to produce a state of plane strain parallel to the x-y plane? Thin-walled Uniform in z-direction Dimension in z-direction that is much smaller than x and y QUESTION 9 What is the major advantage of using the Airy stress function for plane isotropic solids? Reduces the governing equations to only the boundary conditions and compatibility equation Reduces governing equations to a single function with a single unknown QUESTION 10 Airy stress functions are applicable for solving all elasticity problems. True False
2. A tensile test is performed on a bar of Dural (an aluminium alloy) of diameter 15 mm. The bar yields under a load of 30 kN and reaches a maximum load of 46 kN. Estimate the tensile yield stress and tensile strength of Dural
200 stress 150 (MPa) 100 50 0.1 0-2 strain From the tensile stress-strain behavior for the brass specimen the diameter is 12-8 mm Calcalate the folluwing:- %3B 1- The Yield stress. 2-Modulus of elasticity. 3 - The Tensile strength.
kindly help me with this problem choose the correct answer
5. Consider a cylindrical specimen of a steel alloy (Figure 6.22) 10 mm in diameter and 75 mm long that is pulled in tension. Determine its elongation when a load of 20,000 N is applied. Stress (MPa) 600 500 400 300 200 100 0 0.00 0.04 Stress (MPa) 500 400 300 200 100 0.000 0.002 0.004 0.006 0.08 Strain Strain 0.12 0.16 0.20 Figure 6.22 Tensile stress-strain behavior for a steel alloy.