2. A homogeneous, 4m wide, 8m long rectangular gate weighing 3.5kN is held in place by a horizontal flexible cable as shown in the figure. Water acts against the gate, which is hinged at point A. Friction in the hinge is negligible. Determine the tension in the cable. Cable Water Gate 6m 8m Hinge -

Q: aving the stress-strain behavior shown in Animated Figure 6.12. .) i ! HB .) i HRB

A: According to given data  From the stess-strain diagram shown, the tensile strength of brass alloy…

Q: 1. Air (p= 1.23 kg/m³; = 1.79x107 through a 0.08-mm-diameter passa person's lungs at a rate of 10-9…

A:

Q: Could you help with the reaction forces? Dy, Ay, Ax, Dx ? thanks

A:

Q: determine the end moments of the beam shown in Figure 11.9a. Assume support B settles 1.5 in, and…

A:

Q: 1. Calculate the reinforcing steel for a wall with the following dimensions: height 10 ft., long 25…

A: Note:  The given data for the spacing between the bar is 10' which is not possible in any case so,…

Q: Q.2\ A circular column of a cross-section (460)mm in diameter is reinforced with 6 bars of ($25mm),…

A: Diameter of circular column = 460 mmReinforcement = 6 bars of 25 mm dia with 10 mm dia spiral…

Q: 5.0 m 5.50 m 6.0 m 7.0 m 5.0 m (1b0+SN) KN 144 KN E G 120 KN _96 kN M IN 5.0 m 4.50 m 4.20 m 4.0 m

A:

Q: Determine the resultant force and the location of the centre of pressure due to the water pressure…

A:

Q: What area of steel is provided (per ft width) for No 6 @ 9"o.c.? O 0.66 in² O 0.88 in² O 0.59 in² O…

A: In the given question rebar number is given as 6 and 9" bar spacing  Use the table and find area in…

Q: What is Controlled low-strength material ?

A: Controlled low strength material is a fluid material of concrete mix . It is generally used for…

Q: 2. Obtain the interaction diagram for the column section whose dimensions and reinforcement are…

A:

Q: The beam is supported at A and B as shown in (Figure 1). Suppose that F = 6 kip and w = 450 lb/ft.…

A: hinge support at B is givenroller support at A is givenUDL of 0.45k/ft acting over entire spanFind1)…

Q: 4. For the truss shown, determine the forces in members AB, BG, ED and GF 6 kN 2.4m B 24m C 24 m D…

A:

Q: Briefly, Explain How to construct the Forming Limit Diagram (FLD) for any metal?

A: The construct of FLD involves two methods: a theoretical approach and an experimental approach.In…

Q: Assume that the retaining wall shown in Figure is frictionless. Determine the Rankine passive force…

A:

Q: Let w = [w] lb/ft. p) Determine the maximum shear Vmax in the beam. q) Determine the maximum bending…

A: Given  W= 250 lb/ft

Q: 2. According to Boussinesq and Westergaard conditions, determine the resulting load at a point 15 ft…

A:

Q: b) In a hemodialysis machine, blood (p-994 kg/m', u= 3.5 x 10 kg/m.s) is drawn out from a person's…

A: Assume…

Q: 4- A car is traveling at 30 mi/hr when a traffic light 295 ft ahead turns yellow. The light will…

A: The given figure is shown below:

Q: Figure 3 shows a truss where P = 40 kN and Q = 27 kN. The force reaction at A in the y-direction is…

A:

Q: Describe about the homogeneous section.

A: The soil can be classified based on the mixture such as Heterogeneous, and Homogeneous. The…

Q: В 10in 10in D 1.5in 2in

A:

Q: 3) Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and…

A:

Q: FORMULA: The formula for calculating the water content for Plastic limits is as follows: W1 – W2…

A:

Q: 3. The total discharge from A to B in figure is 14 cfs. Determine the discharge in each pipe if the…

A: ● We have to calculate the value of discharge in each of the pipe.

Q: 14" 4.00" 14 1.5" A3 Bare12 Au 8 6 Bars 1. Área of Steel, As, for the column = 2. What % steel is…

A: The area of the steel reinforcement is equal to the sum of the area of the longitudinal…

Q: 2. Cantilever Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W…

A: Given data- X = a1x1 +a2x2+a3x3+a4x4+a5x5+a6x6 Therefore,  X = 12.78 X1=12.78m , X2 =7.78m X3…

Q: The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the…

A:

Q: 2-31. The beam is subjected to the two concentrated loads as shown. Assuming that the foundation…

A:

Q: connecting element line ELU2 150 100 50

A: According to given figure 3, 5mm clearance between  the diameter of holes and screws 750 mm wide…

Q: 1. A soil element is shown in Figure 1 and 2. Determine the following: a. Maximum and minimum…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 4. Exercise 4 ( Westergaard. Determine the stresses of the soil to 8 m depth below the center of the…

A:

Q: Determine the displacement SCIA of the composite bar under the loading as shown. End A is fixed. A,…

A: Deflection is given by:δAB=PABLABAABEABδBC=PBCLBCABCEBCδCA=δAB+δBC

Q: -Compute the plastic section modulus of the following section and its corresponding moment capacity.…

A: to find - plastic section modulus (Zp) and corresponding moment capacity (Mp)

Q: *2-16. Classify each of the structures as statically determinate, statically indeterminate, or…

A: Classify each of the structures statically determinate, statically indeterminate, or unstable.

Q: Define Designing for Flexure

A: The process of bending is known as flexure.

Q: 1. For each of the channel cross sections shown in Figure, compute the area, wetted perimeter, and…

A:

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.