2. A hole was punched on a trapezoidal plate as shown below. Find the distance between thecentroid before the hole was punched and that after the hole was punched.Given : last digit endsGiven : last digit endswith even nos.a = 20b = 40c = 20d = 20with odd nos.a = 25b = 50c = 25d = 25e = 25f= 12.5g = 12.5h = 12.5Ans: D =e = 20f = 10g = 10h = 10Ans:D=3. Blocks A and B have a mass of ma and mol respectively and are connected to the weightlesslinks as shown below. Determine the largest vertical force P that can be applied at the pin Cwithout causing any movement. The coefficient of static friction between the blocks and thecontacting surfaces is f = 0.32.Given : last digit endswith odd nos.f = 0.32M, = 5 kgМь 316 kgGiven : last digit endswith even nos.If = 0.30M, = 3 kgM, = 9 kgAns: P =Ans: P = NAME:STUDENT #:Instructions:1. Mind your own set of problems, Given data for A = all odd numbers and B for all even numbers.Pls write your final answer on red marks.2. Write the problem, FBD and solution to the problems.3. Submit INDIVIDUALLYat my gmail account only on prescribed time allotted.Problems:1. A ladder resting on a horizontal floor leans against a vertical wall at angle e with the floor. Thecoefficient of friction at all surfaces is f. If it is to support a weight of man (W) at the top, whatshould be the limititing value of a? Neglect the weight of the ladder.Weight of ManGiven : last digit endswith odd nos.f = 0.32W = 65kgAns: a =Given : last digit endswith even nos.f = 0.28W = 55kgAns: a =

Answered: Image /qna-images/answer/313f8415-9123-409d-8500-37a13cf230a1.jpg

2. A hole was punched on a trapezoidal plate as shown below. Find the distance between the centroid before the hole was punched and that after the hole was punched. Given : last digit ends with odd nos. a = 25 b = 50 c = 25 d = 25 e = 25 f = 12.5 g = 12.5 h = 12.5 Ans: D = Given : last digit ends with even nos. a = 20 b = 40 c= 20 d = 20 e = 20 f= 10 g = 10 h = 10 Ans:D=

2. A hole was punched on a trapezoidal plate as shown below. Find the distance between the centroid before the hole was punched and that after the hole was punched. Given : last digit ends with odd nos. a = 25 b = 50 c = 25 d = 25 e = 25 f = 12.5 g = 12.5 h = 12.5 Ans: D = Given : last digit ends with even nos. a = 20 b = 40 c= 20 d = 20 e = 20 f= 10 g = 10 h = 10 Ans:D=

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

hello pls help me answer :) thank you
Using foil method, multiply the following: (X+6)2
Find FBC, FBD, FDE, FAB, FBE, FEA, and FCD Show the complete calculation
can you write the answer please
Both ends of the beam are guided or slider support not Fixed support. Plz, solve this problem using stiffness Method and show all the step and alsi draw SFD and BMD My last two digits of my reg.no: 95 Structural Analysis-2
21 B -32 C D Z2 ▼ Part B As shown, a system of cables supports a bucket. (Figure 2) The dimensions in the figure are as follows: ₁ -5.25 ft, 2 = 1.40 ft. y₁=2.20 ft. 3/2=4.50 ft. 2₁ = 3.25 and 22 = 2.30 ft. If the bucket and its contents have a combined weight of W = 11.5 lb, determine TA. TB. and Tc. the tensions in cable segments DA, DB, and DC, respectively. Express your answers numerically in pounds to three significant figures separated by commas. ▸ View Available Hint(s) TA TB.TC Submit 175) ΑΣΦ | 41 Previous Answers Provide Feedback X Incorrect; Try Again; 4 attempts remaining. Part C Complete previous part(s) vec 6 0 BOA ? lb
Solve for the y-component (in mm) of the centroid if that a=2.3, b=2.5, c=4.4, d=8.8, and r=1.5. All dimensions are in inches.Round off only on the final answer expressed in 3 decimal places. Use: 1 inch =25.4 mm
Part A In (Figure 1), r = 30 mm. Locate the centroid a of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. T = 0 mm Submit Previous Answers Correct Figure < 1 of 1 Part B Locate the centroid ī of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. HẢ ? 150 mm = Value Units Submit Previous Answers Request Answer 50 mm 100 mm 100 mm 50 mm