2. A heat pump cycle whose coefficient of performance is 2.5 delivers energy by heat transfer to a dwelling at a rate of 20 kW. a. Determine the net power required to operate the heat pump, in kW. b. Evaluating electricity at $0.08 per determine the cost of electricity in a month when the heat pump operates for 200 hours.

Q: Calculate the blade length of a wind turbine rotor which produces a maximum power of 3 MW at a wind…

A: Given data: Maximum power = 3 MW Speed of wind = 42 km/h Density of air = 1.23 kg/m3 Efficiency of…

Q: The heat exchanger is designed to provide the required amount of thermal energy needed for either…

A: A heat exchanger as the name suggest is used to transfer heat between two fluids at different…

Q: None

A:

Q: A four pitched blades turbine is used to continuously stir a food mixture A which having a viscosity…

A: (A) It is given as baffled tank. reynold number is given as 110000. since it is for a baffled…

Q: estimate the dialy amount of magnesium hydroxide needed for FGD for a 350 MW power plant (0.305…

A: The calculation of the daily amount of magnesium hydroxide necessary for Flue Gas Desulfurization…

Q: A mill produces wet paper containing 15% water by weight (wet basis). This wet paper is fed in a…

A:

Q: a) Pump work (kW) b) Cycle net power (kW) c) Heat transfer in the intermediate heater (kW) d)…

A:

Q: Power of 3 kW is supplied to a machine crushing material at the rate of 0.3 kg/s from 12.5 mm cubes…

A: Given Power required to the crusher, P=3 KW Feed rate, m.=0.3 kg/s Initial diameter of the…

Q: A long cylindrical steel rod is heat treated in an oven that is 7 meters long and is maintained at a…

A: Given data: Length of the cylindrical steel rodd = 7 m Diameter of the rod = 10 cm Initial…

Q: An electrical engineer is analyzing an electroplating run and wants to calculate the charge that has…

A:

Q: q the 10 kg of water at 10°c are electrically heated in a thermally insulated and rigid (1.e…

A:

Q: A manufacturer blends lubricating oil by mixing 300 kg/min of No. 10 oil with 100 kg/min of No. 40…

A: Given  No 10 oil flow rate = 300 kg/min No 40 oil flow rate = 100 kg/min Out let flow rate of…

Q: a) Calculate the pipeline diameter required using the IGT, and Panhandle B equations. b) Explain the…

A:

Q: 3a. Give a general expression for estimating the power consumption in crushers and grinders and…

A:

Q: Problem 3. The head loss (ft) in a piping system is represented by the equation H, = 50 + %3D 6.0…

A: The equation for the head loss in the piping system is given as: Hs=50+6.0Q1002+Hv…

Q: 270 kW of power is required to crush 150 tonnes/h ofa material. f 80% of the feed passes througha…

A:

Q: Problem 2 A building requires 5 x 105 BTU per day to maintain its temperature at 70°F when the…

A:

Q: Q16. A material is crushed in a jaw crusher and the average size of the particle is reduced from 5…

A: Given data: Case 1:Initial size of the particle; Di=5 cm=50 mmFinal size of the particle; Df=1.3…

Q: We wish to calculate the internal heat transfer coefficient for water flowing at 0.00958 m/s through…

A:

Q: Q.10Calculate the increase in enthalpy of water in the system as in figure below, where zı=10 ft,…

A: The increase in enthalpy is obtained from the steady flow energy equation. The steady flow energy…

Q: A gas condensate transmission line transports 263 MMSCF/day of gas from a processing plant to a…

A:

Q: Pressure 300 kPa with piston on stop, cylinder volume 0.04 m3 and the degree of dryness 50 percent…

A: Given, initial pressure, P1 = 300 kPa initial volume, V1 = 0.04 m3 Amount of water in the piston is…

Q: Write a report on Reynolds Number's experience. Where the report includes: 1- An introduction to the…

A: 1. INTRODUCTION In nature and in laboratory experiments, flow may occur under two very different…

Q: Water at 15.56°C is to be heated in a 2-mm-ID tube until the exit temperature reaches 26.67°C. The…

A: Given: The temperature of water T = 15.56 oC, Exit temperature Te =26.67 oC At Tb = 21.11 oC the…

Q: 15 MT/hr of the ore is fed to a single crushing roll which runs at 30 revolutions per minute. The…

A: It is given that  ore is fed into a single crushing roll running at .Diameter ratio Screen analysis…

Q: cycle time for maximum filtrate

A:

Q: 1. A pump when tested at 1200 rpm gave the following data: Flow Q (m³/s) Head generated H (m) 0.01…

A:

Q: A coal-burning electric generating plant emits 1.5 kg/min of SO2 from a stack with an effective…

A: Given wind speed is 5 m/s.From Atmospheric Stability under Various Conditions table (which is given…

Q: What is wrong with the following distillation setup? (Select all that apply) A. The thermometer bulb…

A: Distillation is process of separation of fluid into its pure constituent.

Q: A coal-burning steam power plant produces a net power of 300 MW with an overall thermal efficiency…

A: Given, The net power produced = 300 MW Overall thermal efficiency = 32% Actual gravimetric air fuel…

Q: Fixed volume (1 m3 ) in a tank initially 2 kg of water is at a temperature of 100 C. Tank is…

A: Given data: Volume of tank = 1 m3 Mass of water = 2 kg Initial temperature = 100 0C Final…

Q: A system is a connection of equipment connected together to perform a specific function. The system…

A: To analyze each device in the diagram and answer  1) which contact device is used in the given…

Q: In a faraway land an engineer is observing a construction working on a snow from a pavement. What he…

A: Given that- Mass flow rate of snow m. =100 lb/s Height of bucket of snow, h= 305 cm =10 ft Velocity…

Q: vessel needs to design the distillation column. The specification for of a sieve plate column is…

A: The design of mechanical equipment considers a lot of factors. Since distillation column is a tall…

Q: Estimate the annualised operating cost for the cyclone of Problem 4.14 assuming the cyclone operates…

A: Given In 2008(Present) Fan efficiency = 0.6 Electricity costs =$0.08/kWh Pressure drop ∆P=6.0 in…

Q: Q3/The supply ductwork for a hotel building is shown below. Determine : - 1. Size of main duct and…

A: A supply ductwork for a hotel buil;ding is given, where,the velocity is given as, ,main duct and…

Q: Engine oil flows through a 50 mm diameter tube at an average temperature of 147°C. The flow velocity…

A: Given, Diameter D    = 50 mm = 0.050 m Average temperature Tm= 147°C Velocity U= 80 cm/s = 0.80 m/s…

Q: Water flows through a shower head steadily at a rate of 8 kg/min. The water is heated in an electric…

A:

Q: Moving bed catalytic cracking explain in detailed the following diagram. Moving Bed (fluid-bed)…

A: The process flow diagram of FCC unit is to be explained. Catalytic carking is chemical process in…

Q: Calculate the power needed to reduce 100 ton/hr of quartz (work index = 17.5 kW-hr/ton) in a…

A:

Q: (a.) A power of 5 kW is supplied to a machine crushing material at the rate of 0.5 kg/s from 12.5 mm…

A: