2. A crossed belt goes around the pulleys A and B having radii of 14 cm and 7 cm, respectively. The distance between centers of the two pulleys is 36 cm. a) Determine the angle of contact of the belt on the bigger pulley. b) Determine the length of the common internal tangent. c) Determine the total length of the belt. ----- 14 21 ----- ---

Q: 250 mm fe = 21 MPa fy = 415 MPa n = 9 Tension reinforcement: 2 – 25mmØ RSB 1.4 Pmin fy Pmax = 0.75Pp…

A: Moment Capacity - The moment capacity is maximum bending moment that can be resisted by an element…

Q: Determine the height and the following reactions of the cable

A: Given: To find: The height and the support reactions of the cable

Q: Cables AB and BC are tied to the ring at B. Find W, and W, knowing the barrel weighs 450. Ignore the…

A: Given :

Q: Determine the minimum downward force to keep the block from slipping. The block weighs W kN. The…

A:

Q: Question 3: calculate the forces in all the members of Cable R = Last two digit of Roll No. S 2.74 m…

A:

Q: I. Method of Members 1. The portable table shown is to support a load P = 1.5 kN at a variable…

A: P (load) = 1.5KN L = 1.5m

Q: QUESTION 4) The cross-section and the loading of the overhanging beam is given in the figure. If the…

A: For any beam when load acts on them they undergoes the stress, for loading application beam shows…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: De Ex 2m

A:

Q: has a diameter of 40 mm and 24 mm, respectively. A horizontal member AC carries a linearly…

A: Equilibrium Condition is applied . Shear stress = shear force / Area  Tensile force in steel cable…

Q: The length of the (12 mm) diameter steel wire CD has been adjusted so that with no applied, a gap of…

A: Length of steel wire, CD= LCD= 3m Diameter of steel wire, CD=DCD= 12 mm Modulus of elasticity, E=…

Q: 9. The beam loaded as shown is supported by a hinge at A and a roller at B. Find the reactions in…

A: As per our company guidelines we are supposed to answer only one question kindly repost other…

Q: A cable is used as a laundry washing line whose end points are fixed at A and B. The clothes on the…

A:

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A:

Q: Problem #1 Beam ABCD has an internal hinge at C and rollers at B and D. Draw the lokip necessary…

A:

Q: he spool has a mass of 30 kg and a radius of gy o = 0.25 m. Block A has a mass of 25 kg, and 3 has a…

A: mA=25kgmb=10kgrA=0.32mrB=0.18mvA=6msvA=ωrAω=60.32rads=19.75vB=ωrB=60.320.18=3.375ms

Q: DETERMINE THE PROPER POSITION OF THE C-PURLIN IF THE LOAD IS SUBJECTED DOWNWARD. 1. DETERMINE THE…

A: The C-section is divided into 3 rectangles as shown below:

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E = 29 000 ksi). If the end C is…

A: Reference : Engineering mechanics, Elongation and displacement due to load acting on the rod. Given…

Q: The 6.9-lb force is applied at point A of the crank assembly. Determine the moment of this force…

A: Given:Required:Moment of force about point O

Q: tensions in cables AB, AC, and AD.

A: Lami's Theorem- If three coplanar forces acting at a point be in equilibrium, then each force is…

Q: A load of 175 N applied to the members shown below causes a tension of 40Ó N in cable DC. a)…

A:

Q: I need some help with part c

A: c. Given Data, RCy=20 N Free body diagram for the figure is given as, tanα=2410α=tan-12.4α=67.3°

Q: Homework 1 Q1) The frame shown below supports 100lb weight. The cable is attached at A and passes…

A:

Q: 7. The force F on the piston in Figure 5 causes the link AB to exert a force P = 2 kN on the pin B…

A: T

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: . Determine the rotation angle of pulley D with

A:

Q: P (kN) Şekildeki kafes sistemde çubuk kuvvetlerini Basınç-çekme hesaplayınız. durumlarını A B…

A:

Q: Calculate the magnitude of the tension T and the angle for which the eye bolt will be under a…

A: For the given eye bolt:

Q: 3. For the cables shown in Figure ST – 064 1. Compute the tension in each segment if P = 400 N. 2.…

A:

Q: Determine the reactions at Pin A, Rocker B and Pin C Note that piece ACF and BCDE are each one…

A:

Q: 9 ft- Problem 3. The frame that supports the 1000 lb anvil consists of members ABCDE, A 3 t B 1 ft…

A: Given- load= 1000 lb  To find- Reaction support and members force

Q: Replace the forces acting on the plate by a wrench. Specify the force and couple moment for the…

A: Consider the figure,

Q: Determine the angle between cable AC and strut AO. Determine the magnitude of AC and AO.

A: Given: Required; Angle between AC and AO  Magnitude of AC and AO

Q: AT- section is the cross section of a loaded beam as shown.

A: Given: Simply supported beam with an overhang. The beam carries a uniformly varying load.  To…

Q: -2.4 m-t- 6m -2.4m- 1. For the electric transmission tower shown, 1.2 m a. Determine if the truss is…

A: A electric transmission tower is given in the question supported on hinge support at both the ends.…

Q: 1.3 ft 200 Ib

A:

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.