2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to Cand D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions.

Q: A large three-dimensional pipe of circular section with radius R = 0.2 m is part of a hydroelectric…

A: Consider expression for velocity profile.Here R indicates radius of pipe, r is radial distance from…

Q: X 400 mm Z 8 rad/s² 2 rad/s 800 mm The velocity is: m/s to one decimal place). S The acceleration…

A:

Q: 4-94. Express the moment of the couple acting on the rod in Cartesian vector form. What is the…

A: Given:- F1=-4i¯+3 j¯-4k¯ F2=4i¯-3 j¯+4k¯  To find:-Moment of couple acting on rod

Q: owing comp ollow shaft C ed torque of

A:

Q: The a-t graph of the bullet train is shown. If the train starts from rest, determine the elapsed…

A:

Q: : Determine the moment of the force about point A.

A: Given: TO determine: Moment about A

Q: If P = 698 N, and the coefficient of kinetic friction between the 50-kg crate and the inclined plane…

A: Given data: P=698 Nm=50 Kgθ=30°μ=0.25

Q: The vector A is directed due west with a magnitude of 5 N. Vector B is directed due north with a…

A: As per given question  P=5N Q=12 We have to find value A+B

Q: Given: Given: Prior to launch, Balloon tethered by lines AB, AC, and AD. Mass of the balloon is 90…

A: Hi,   We can solve only first question for you since the exact one is not specified. Please resubmit…

Q: Determine the length b of the triangular load and its position a on the beam such that the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: 2–33. Determine the magnitude of the resultant force and its direction, measured clockwise from the…

A:

Q: 2. A hook is subjected to three forces A, B, and C as shown. Force A = 30 kN and force B = 50 kN.…

A:

Q: 4. The cross sectional area of each member of the truss is 1.6 in?. Calculate the stresses in…

A: GIVEN DATA - A PLANE TRUSS GIVEN WITH AREA 1.6in2 WE HAVE TO FIND STRESS IN GIVEN MEMBER

Q: Instruction: Determine the moment of the force about point A.

A: Given Structure in loading To find Moment about A

Q: Four parallel forces act on the plate as shown. For the force system shown, find the equivalent…

A:

Q: 8. The figure shows a roof truss and the detail of the connection at joint B .Members BC and BE are…

A:

Q: 1. Plate ABCDEF is a sliding door supported by a frictionless linear bearing at A and a frictionless…

A: The total weight of gate is

Q: 6. The plastic sheet, 1/2 in. thick, is bonded to the pin-jointed steel frame. Determine the…

A: GIVEN DATA- G=70*10^3 psi Thickness t=1/2in we have to find value of force P

Q: 2. The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical…

A:

Q: 6. x9(x) = qo sin- L Find M(x), V(x) using π.χ. d²M dx² = q(x) j

A: In this problem, it is asking about question (6) only so we will provide the solution for question…

Q: 5. When unloaded, bars AB and AC are each 36 - in long and have a cross-sectional area of 2 in.…

A:

Q: Stage Design A cable is used to support an actor as he swings onto the stage. Now suppose the…

A:

Q: Metrology Discuss both figures and explain which one comply with Taylor principle and why?

A: Taylor's principle in metrology says that the GO gauge should check all the dimensions of the…

Q: 3. The following data are given for a U-tube steam generator. Tube mass flow rate m =70E6 lbm/h,…

A: Head represents by the body force is known as hydrostatic head because of gravity when forced…

Q: The ball is kicked from point A with the initial velocity VẠ = 10 m/s. Determine the range R, and…

A: A reaction force opposes an action force by acting in the opposite direction. During sliding,…

Q: 9 m long, determine the x, y, z coordinates of point A.

A: we will calculate the direction cosines of this force vector  first we calculate the magnitude of…

Q: Given: Airplane sketch with wheels locked at B; wheels at A free to turn; Force at T is horizontal…

A: As per the bartelby guidelines only one question is allowed to solve. As per the students request…

Q: Given: The two systems are equivalent systems Determine: Ax, AY, MA 600 mm 20 N 400 mm 400 mm 30 N…

A: Hi, We can provide the solution for first question only since you have not mentioned it clearly.…

Q: 0 kN. Determine the required cross-sectional area of the wable stresses are 6 MPa for concrete and…

A: Need to determine the cross-Sectional area of reinforcing steel

Q: 2. Link BD is made of brass (E = 103 GPa ) and has a cross-sectional area of 258 mm?. Link CE is…

A:

Q: 7 ►X a L a. Find reaction at x = 0. b. Find M(x) and V(x) Mo j Li 1

A:

Q: 3. Bars AB, CD, and EF cach have a cross-sectional area of 25 mm and modulus of clasticity E=200…

A:

Q: 100 lb 50 Ib 45 250 lb 2. Determine M, P, and Q in the figure shown so that the resultant of the…

A:

Q: Refrigerant 134a enters a well-insulated nozzle at 200 lbf/in.2, 170°F, with a velocity of 120 ft/s…

A:

Q: In guarding against excessive deflection due to an applied force F, the designer determined the…

A: Given Data: Maximum deflection(δ) of a cantilevered beam at its free end to be given by the…

Q: Determine the following based on the given illustration: a) Area of the Composite figure b)…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.