2. A 10mm diameter hole is to be drilled in a 5mm HSS plate by EDM using RC circuit. The required surface finish is 20um. Determine specifications of a capacitor to be used when supply and discharge voltages are 220V and 150V, respectively. Use resistance as 502 and value of the constant as 0.4. Also estimate time required to complete the job.

Q: (s) G₁ H₁ G₂ Hy G3 H₂ G₁ C(s)

A:

Q: RI Rc Vcc R2 RE Ry 0100555-9870479447 VE g160100555 - 9870479447 The values of some resistors and…

A: In small signal model capacitor CE is short circuited hence resistance RE is also shorted.   In the…

Q: Design a five-bit variable resistor network DAC using R1=0.5 K ohm and RL=4 K ohm resistors for (0 =…

A:

Q: A) Write the nodal equations of the following circuit

A:

Q: Q5/ The Gray code ( 1011011101)=

A:

Q: PB CR2 米 CR3 CR1 CR2

A: Please find your answer below in step 2

Q: An RTD has R=D159 Q at -80C, what is the sensor resistor at 86 °C, let a = 1 x 10-4°C.

A:

Q: Q2: A program to calculate the sum of squares of numbers from 1 to n.

A: matlab program is written below

Q: VCIS for Floating Load – Examples Example D1: Determine load current (assuming linear operation) b.…

A:

Q: esign values for Ra, Rb, and Rc so that Vout is etermined by the following equation. Rd = 10k Ra V+…

A:

Q: Question 1 In the IC world, there's a always a cost for designing chips for different types of…

A: 1..(a)..speed of IC or CMOS is directly proportional to power consumption 2..(c)CMOS is a inverter…

Q: am very lost on the steps it takes to complete these problems from start to finish, If at all…

A:

Q: b. In (1- jv3

A: The basic complex problem can be solved easily as shown below.

Q: 1. Add the following numbers that are in 2's complement (n=7). Show your work, and convert all…

A:

Q: The electric field in some region is found to be E = RkR³ (V/m) in spherical coordinates (R, 0,6).…

A: E=RKR^3(V/m)

Q: CLOCK Prob. 5.17 Clock 1. T o 10 Q Q Qo 8 10 Q QI T Qf Q Q2 000 001010 111 1000 1001 1010 (111

A:

Q: The number (83.45) in base (r=10) can be represented as:

A: Here it is asked to find the decimal number in terms of power of base 10.

Q: Use Tinkercad to wire and test following Digital Circuit Implement a BCD-to-Excess-3 code converter…

A: We need to implement a BCD-Excess 3 code converter and the output from Excess-3 circuit will be…

Q: b) represented R(s) K A manufacturing process is by the following block diagram: H₂(s) G₁(s) H₂(s)…

A:

Q: For the circuit below, fill in the values for the mesh equations. Between the vaiables there is a…

A: In this answer let us use the mesh analysis to find the required parameters as shown below.

Q: reduce the following diagrams to a single block

A:

Q: Calculate the value of R needed to have a critically damped response. 0.01 F 0.01 F 16 R www 4 H m 4…

A:

Q: R(s) Answer: T(S) G1(s) G₂(s) G3(s) G4(s) G5(s) G7(s) G6(s) C(s) G6 G4+G6G3+G6 G5 G3 + G6 G5 G₂…

A: Given Data:A block diagram model with,Input Output To Find:The transfer function.

Q: Vcc V+ Vout Ra V. V- Va -Vcc Rb Rd Vb Rc R4 Vc +

A: Find the output voltage interms of input voltages for the given op amp circuit ?

Q: Q2/Chose the correct answer for the output Q3 of the following circuit ( Assume that A=…

A: We need to find out output for final flop.

Q: Obtain the transfer functions C(s)/R(s) and C(s)/D(s) of the system shown in Figure R(1) Ge G₁ H H₂…

A: Introduction Transfer Function: For all conceivable input values, a transfer function shows the…

Q: A block diagram is shown in the following figure, try to calculate C(s)/ R(s). R(s) E(s) G₁ H₁ H₂ G₂…

A: In this question, we need to determine the transfer function.we solve this problem using mason gain…

Q: THE COUNCIL OF A CERTAIN COMPANY IS COMPOSED BY THE PRESIDENT (P), A DIRECTOR (D), A TREASURER (T)…

A:

Q: Problem 1 Determine the differential equation governing the voltage across the current source at t>…

A: In this question,  Time t<0 switch open Time t= 0 switch close.  Determine the differential…

Q: Develop a circuit that will provide an output voltage that is -4 Vm if the input voltage is Vmsinwt

A: To obtain the -Vm at the output, we need to design a voltage quadrupler. The circuit of the voltage…

Q: According to the circuit in below, find- out the function describes correctly the circuit output (F)…

A: In this answer we will try to find out the equivalent expression of F as shown below.

Q: B) A strain gauge has a resistance of 1000 2 is connected as a one arm of a whetstone bridge to…

A: The solution can be achieved as follows.

Q: Q2/ Find and plot the linear convolution between x and y x(n)= u(n+25)-u(n-25) y(n)= u(n+30)-u(n-30)

A: In this question,  Find the convolution between x and y.  We know convolution property of the Step…

Q: Create the simplified circuit for the ‘A’ segment . Here, the output FA from your circuit for…

A: Digital electronics problem .. Look below for the solution once..

Q: Create five Kirchhoff's Current Law (KCL) problem with figure and solve it(Show complete solution)

A:

Q: Chose the correct answer for the output Q3 of the following circuit (Assume that A= 001100,B=111100,…

A:

Q: can you please solve it in the other way like there's elimination of equations

A:

Q: # Design to implement the a circuit with 2 op-ams following functions Of = S(4x + ³ydt f = − 4.5m +…

A:

Q: R(s) a) Find all loops, Pk's, Ak's, and A for E(s)/R(s). b) Use Mason's Rule and the result of part…

A: As per Bartleby guideline we need to answer the first three questions only. Kindly repost the rest…

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.