2. A 100-pound weight is suspended from a verticalspring whose module is 100 pounds per foot. Theweight is pulled downward 9 inches from itsequilibrium position and released. Viscous fluidexerts 90 lbs of force when the plunger movesthrough it at 3 ft/sec;2.a What is the damping condition?Write the equation which describes the motion of theweights. Show graph.2.b displacement2.c velocity2.d acceleration

Name: 2. A 100-pound weight is suspended from a verticalspring whose module
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2. A 100-pound weight is suspended from a verticalspring whose module is 100 pounds per foot. Theweight is pulled downward 9 inches from itsequilibrium position and released. Viscous fluidexerts 90 lbs of force when the plunger movesthrough it at 3

Answered: Image /qna-images/answer/920022c7-bea1-40ca-a91d-9ca40e9edc2d.jpg

Engineering

Mechanical Engineering

2. A 100-pound weight is suspended from a ve spring whose module is 100 pounds per foot. 1 weight is pulled downward 9 inches from its equilibrium position and released. Viscous flui exerts 90 lbs of force when the plunger moves through it at 3 ft/sec;

2. A 100-pound weight is suspended from a ve spring whose module is 100 pounds per foot. 1 weight is pulled downward 9 inches from its equilibrium position and released. Viscous flui exerts 90 lbs of force when the plunger moves through it at 3 ft/sec;

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You are about to ride a roller-coaster at Disney. The ride is a single-person ride with a drop of 25.0 meters and a plunger/piston system that makes the ride stop. There is a 250 kg water cylinder attached to the plunger/piston. The cart weighs about 75.0 kg and begins at the top of the circuit at a standstill. To get the total mass of the cart during the ride, you must add your weight (55KG) to the cart's overall weight. According to analysis, friction in the wheels and axles creates 2750 J of combined thermal and sound energy when the cart moves along the track. The bottom of the device's plunger/piston is designed to stop the cart at a max acceleration of 5.00 g's (49.0 m/s2). Question: Question #5: The plunger/piston compresses the water inside the cylinder, which is thenturned into thermal energy within the water. Determine the temperature change of the waterin the cylinder as it pulls the cart to a stop if the specific heat capacity of water is 4184J/kg°C (assuming 100 percent…
A69 A typical escalator in the London Under- ground rises at an angle of 30° to the horizontal. It lifts people through a vertical height of 15 m in 1.0 minute. Assuming all the passengers stand still whilst on the escalator, 75 people can step on at the bottom and off at the top in each minute. Take the average mass of a passenger to be 75 kg. (a) Find the power needed to lift the passen- gers when the escalator is fully laden. For this calculation assume that any kinetic energy given to the passengers by the escalator is negligible. (b) The frictional force in the escalator system is 1.4 x 10*N when the escalator is fully laden. Calculate the power needed to overcome the friction. Hence find the power input for the motor driving the fully laden escalator, given that the motor is only 70% efficient. (c) When the passengers walk up the moving escalator, is more or less power required by the motor to maintain the escalator at the same speed? Explain your answer. (0 & C, '90]
The angular momentum of the body is equal to?
b) Figure Q3 shows a vehicle uses water scooping to slow down. The scoop is 3-m wide. Draw the free body diagram of the scoop. Determine the amount of force exerted on the scoop. If the force exerted by the flow to the scoop is 460 kN, determine the velocity of the vehicle. The vehicle scoops off 10 cm of water.
The Super Soaker XP30 is a marvel of hydraulic dispersion weaponry. By pumping on the handle, you charge the chamber to high pressure. The pressure is maintained until you pull the trigger at which point the water (? = 1000 kg/m3) is released at high velocity.You have charged your pressure chamber to an absolute pressure of P1 = 697500 Pascals, much higher than today's outside air pressure of 101300 Pascals. The pressure chamber is location at a height of y1 = 0.103 meters above the exit point. The exit point has a small opening with radius r = 0.0033 meters.Determine all the following:The velocity at which the water exits the Super Soaker: v2 = m/sThe mass flow rate through the exit: kg/secThe volume flow rate through the exit: m3/secNOTE: You may treat the water chamber as a "tank" and approximate the water velocity there to be zero.
For the cart of figure, compute the force on the wheels caused by deflecting the jet and thecompression of the spring, if its stiffness is 1.6 kN/m.
Your engineering firm is asked to specify the maximum load for theelevators in a new building. Each elevator has a mass 490 kg when empty and maximumacceleration 2.24 m/s2. The elevator cables can withstand a maximum tension of 19.5 kN beforebreaking. For safety, you need to ensure that the tension never exceeds two-thirds of that value.What is the maximum load that the elevator can safely carry? How many70-kg people is that?Briefly but clearly explain the reasoning for your choice of the sign of the acceleration.
2.30 A cart is moved by the action of a high-speed jet as shown. If the cart moves on frictionless wheels, determine the initial acceleration of the cart (the mass of the water in the cart is negligible). The mass of the cart is lO slugs and the cart starts from rest. What equation governs the cart velocity Vc if the water collected in the cart is not neglected? A numerical solution using the computer could be developed. Hint: Use Conservation of Mass to develop a differential equation for mass as a function of time, m(t). Use Conservation of Momentum to develop a differential equation for Vc. You must retain the inertial force term because the coordinate system is attached to the cart, and the cart is moving. You have 2 coupled differential equations that must be solved numerically. (The numerical solution is not a part of this problem, but will be provided!)
As shown in Figure 2.3, the total height of the liquid in the canal in Part (a) is now increased to 3R. Determine the minimum force F applied at B to prevent the gate ABC from opening (i.e. turning anticlockwise about the hinge A). Neglect the weight of the gate and friction in the hinge. F- 2R Air с B Gate R Air Liquid Hinge Figure 2.3 Р 777. gv