2) The temperature distribution in the square chimney is to be analyzed by the finite difference method. Determine the temperature at the nodes of the grid shown. T-120 °C Ta400 °C le 16' 6 cm 12 cm 18 cm

Q: y

A:

Q: Find the value of a. TO a. Vs +3

A:

Q: . Find the volume of a bronze bushing if it's inside diameter is 1 inch, outside diameter is 1.50…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: Question 18 Simplify (−4 − 4j) O 1.412-45° O 1.41/225° O 1.414-225° O 1.41/45°

A: Simply the above expression

Q: PO 8 in.

A: Redraw the following figure for the given question.

Q: If Ma- 68.5 kN-m and Mc- 56.0 kN-m, use the graphical method to construct the bending -moment…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: A plastic rod AB of length L = 520 mm has a diameter d, = 30 mm as shown in Figure Q2(b). A plastic…

A: For the given composite bar it is required to determine: (1) Total elongation of the bar when P = 15…

Q: - х a = 6 in b = 0.7 in C = 2 in

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 6xty- 2

A: Information given⇒ 6x4y-22x-1y42

Q: Determine the answer by caliper reading

A: Vernier caliper A vernier scale is a visual aid to take associate degree correct measuring reading…

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: what is part number 4

A: Solution:

Q: Fint total force acting on point A. Point A can be anywhere.

A:

Q: (Determine the (f_x ) when force 80 N and angle 30° on the axis (X .A 69N .B 69.28lb .C 69.28N .D…

A:

Q: What is the moment's function?

A: Moment deals with the physical quantities situated at some distance relative to the reference point.…

Q: Solve both and show all parts and solutions

A: The power to input shaft is The speed of gear of input shaft is The gear ratio is The loss in power…

Q: R D.

A:

Q: What is the average force magnitude?

A:

Q: In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a…

A: According to the question data MA=200lb.inclockwise   and the figure  We need to find Force F to…

Q: G Determine the equillalent. tiffness for the dreegreem

A: Solution:

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: slove f

A:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: handle should be identified as a point of interest. Determine the Degree of freedom.

A:

Q: I tried the degree both 51 and 50.99 but it is incorrect. Plz help.

A: