2- The person using the hammer is applying 30 N force in the direction shown. i- Determine the moment at point A. ii- What is the strongest nail this person can remove? 45 8ст 30ст Зст B

Q: Don't Copy ,I need Correct Handwritten Solution Only Asap (Including FBD) 1)The support at O can…

A:

Q: Determine the manometer reading as shown in the figure, when the velocity of fluid flowing through a…

A: Given data:  The diameter of the pipe is d1=75 mm The fluid velocity is v=0.6 m/s

Q: Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X)

A:

Q: A closed cylindrical vessel, 3m in diameter and 8m high is shown. Assuming that C of orifice is…

A: we have to determine the flow rate

Q: What would be the resultant force F of the triangular distributed load and its location d measured…

A: Triangular load is also termed as uniformly distributed load.  The magnitude of the triangular…

Q: Q- 6- Resolve the force 250N into rectangular components 250 N 16 9. 12

A: Here, Magnitude of the force = 250 N   For the given triangle, missing angle θ can be found by,…

Q: L1=4 in , L2=3 in, L3=1.5 in , h1=5 in , h2=6 in , f=7 lb , p= 45 lb. determine the proper angle in…

A:

Q: R2-7. Determine the angle 0 between the edges of the sheet-metal bracket. -400 mm 250 mm x. 300 mm…

A:

Q: Determine the position of the neutral axis of a curved bar subjected to flexure by a couple shown in…

A: The position of the neutral axis of a curved bar subjected to flexure by a pair must be…

Q: Solve vectorially the rotation effect that F force will create on the hinge axis.F=610

A: Data given-  F = 610 N

Q: If the diameter (d) of wheel is reduced in half times in size, Then the torque produced in the wheel…

A: If the diameter (d) of wheel is reduced to half times in size, Then the torque produced in the wheel…

Q: Q1: Determine the moment of the force 225 N about the points A, B, and C.

A: Given data Force = 225 N

Q: F3 FR = 120 N F2 = 110 N %3D HW04-2 p0o Three forces act on the ring. If the resultant force FR has…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Q1: The 120-N force is applied as shown to one end of the curved wrench. F=100N If a= 55°, calculate…

A:

Q: 2-81. Determine the angle e between the two cables attached to the post. F = 400 N 35° 120° 60° 20°…

A:

Q: Two reservoirs are connected by 198ft of 2-in diameter tubing. What is the flow rate when the…

A: The calculated flow rate in ft3/s.

Q: Determine the value of P acting to the left that is required to pull the wedge out from under the…

A:

Q: Q3: Find the moment a bout at point A 100mm 100mm 200N 150N 45 --A 15N.m 200mm 40N.m 80N

A: Given Structure To find Moment at point A

Q: The force acting on the gear tooth is F = 20 lb. Resolve this force into two components acting along…

A: Free body diagram FREE BODY DIAGRAM is a diagram of the system which represents all the forces…

Q: C2X8 X Given the 50 lb. force at point A, replace it by a force acting at B. B 50# A

A:

Q: s' L Oetermne the value s the Reaction A 2. Determine the valueg the Reactions L 9, the value 4 The…

A:

Q: Q1: Determine the moments about point ( A ) due to the forces applied on the cantilevered beam. 4 KN…

A:

Q: Draw the FAD @ rod AB FBD

A: FBD is given below:

Q: If F = 125N, F2 determine the resultant force in the figure. = 25N and F3 = 150N,

A:

Q: If the value of alpha is 30 degrees calculate the moment of F about the center O of the bolt. F =…

A:

Q: 2-13 The force acting on the gear tooth is F 20 tb. Resolve this force into two components acting…

A: