(2) Sally starts eluting her column with petroleum ether in hopes of separating her 50:50 ferrocene: fluorenone mixture. She notices her mobile phase getting low when there is limited separation between her two components. She eagerly adds more solvent to avoid her column from drying out. Sally then realizes she poured from her 1:1 petroleum ether: diethyl ether beaker rather than her petroleum ether beaker. (a) Using the molecular view below, explain how this would impact her product elution from the column. top of column -- buret wall Al UU Al O: 0: AI :0: H H buret wall bottom of column (b) How does this error impact her experimental results? (c) Using pictures and words, how could Sally analyze the purity of her product?

(2) Sally starts eluting her column with petroleum ether in hopes of separating her 50:50 ferrocene: fluorenone mixture. She notices her mobile phase getting low when there is limited separation between her two components. She eagerly adds more solvent to avoid her column from drying out. Sally then realizes she poured from her 1:1 petroleum ether: diethyl ether beaker rather than her petroleum ether beaker. (a) Using the molecular view below, explain how this would impact her product elution from the column. top of column -- buret wall Al UU Al O: 0: AI :0: H H buret wall bottom of column (b) How does this error impact her experimental results? (c) Using pictures and words, how could Sally analyze the purity of her product?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Consider Table 1, which lists the volumes of the Fe3+ and SCN- solutions used for the continuous variation method. Note that each of the stock solutions is 0.002 M before mixing. What are the initial concentrations of Fe3+ and SCN- for solution 4, where the volumes are both 5 mL? [Initial meaning after they are mixed, but before]they reach equilibrium)
What mass of MgCl₂ 6H₂O is required to make a 0.200 dm³ stock solution containing 25.0 ppm Mg(II)? What volumes of this stock solution are required to make 10.0 cm³ standard solutions containing 5.00, 1.00 and 0.10 ppm Mg(II)?
In normal phase TLC, the mobile phase is + polar than the stationary phase. Consider the TLC plate below, which was developed using a 25% ethyl acetate:hexane solution. If this same mixture of compounds was developed on a TLC using a 50% ethyl acetate:hexane solution, the orange spot would A mixture of two compounds was developed on a TLC plate. The result is shown below. What is one thing the chemist can do to get better results? In normal phase TLC, the mobile phase is : polar than the stationary phase. Consider the TLC plate below, which was c exane solution. If this same mixture of compounds was developed on a TLC using a 50% ethyl acetate:hexane solution, the orange spot would less sometimes more, sometimes less more A mixture of two compounds was developed on a TLC plate. The result is shown below. What is one thing the chemist can do to get better results?
If the endpoints you reached during standardization of your NaOH solution were very precise (relative average deviation if 0.03%) but were all overshot (meaning too much NaOH was added an you passedyour equivalence point), is the reported molar concentration of the acid solution from this experiment greater than , less than or equal to the true concentration? Explain.
Determine a procedure to accurately create a 1.5•10^-6 mg Fe/mL solution using a 0.0500 mg Fe/mL standard solution and only having access to 100.0 mL volumetric flasks and 1.00, 2.00, 3.00, 4.00, 5.00 and 10.00 mL volumetric pipets. (You may have it make more than one solution by dilution to accomplish this)
10 mL of a liquid composed only of carbon and hydrogen is added to a separatory funnel containing 100 mL of water and 100 mL of hexane, an organic solvent. After shaking, the liquids are transferred to graduated cylinders. What are the volumes of the aqueous and organic layers? Aqueous 105 mL; organic 105 mL Aqueous 100 mL; organic 110 mL Aqueous 110 mL; organic 100 mL Cannot be determined O O O O
2. A gas chromatogram of a four-(4)-component mixture had the following areas and retention times (RT). Component ABCD (RT) (min) 2.564 5.241 1.904 3.217 Area (mm²) 2341 1278 4302 1987 A. Which compound do you suspect is the most volatile? Why? B. Calculate the percent composition of component D.
2. Prepare a Temperature vs Time cooling curve for each of the two trials involving the lauric acid/stearic acid mixtures. Perform a linear regression analysis on the cooling and freezing regions as before. Calculate the point of intersection and identify this point on each graph by inserting a text box and arrow. Report the freezing point for each of the two trials [T(1) and T (2)]. Freezing point (1st trial of lauric acid) T(1) = Freezing point (2nd trial of lauric acid) T(2) =
Preparation of 0.25N NaOH Objective: Apparatus and Materials: Procedure : Calculate the exact mass of NaOH needed to prepare 1.0L of 0.25N NaOH for standardization. Show your computations. Using the triple beam balance, weigh the desired amount of NaOH. Place the weighed amount of NaOH into the 500 mL volumetric flask and add distilled water until it reaches the mark. Agitate and transfer the solution into the reagent bottle. Add again distilled water to the same volumetric flask until it reaches the mark and pour it to the same reagent bottle, thus having a total volume of 1.0 L. Label the reagent bottle, 0.25N NaOH. Data and Computations: Conclusion: