Q2- Indicate whether the following statements are true or false and correct the false statements1- The brushes of d.c machine always are placed at the magnetic neutral axis2- The field current of d.c shunt generator is not affected by load current.3-The armature voltage of d.c series generator is not affected by load current.4- A lap winding is most suitable for higher voltage rating machines5- In de generator, the critical resistance can be increased by increasing its speed6-In LAP winding the front pitch equal to (yr Ye- yb).7- The speed of d.c series motor is decreased if the armature current is decreased8- The compensating winding carrying the field current9- By tapping field method, the speed of d.c series motor can be controlled below ratedvalue10- To solve the Commutation Problem in small machines, this can be achieved by increasing thebrush width

Given A few statements we need to find whether they are true or false. According to the bartleby…

2- Indicate whether the following statements are true or false and correct the false statements 1- The brushes of d.c machine always are placed at the magnetic neutral axis 2- The field current of d.c shunt generator is not affected by load current. 3-The armature voltage of d.c series generator is not affected by load current. lon winding is mos suitabl for higher voltage rating machin

2- Indicate whether the following statements are true or false and correct the false statements 1- The brushes of d.c machine always are placed at the magnetic neutral axis 2- The field current of d.c shunt generator is not affected by load current. 3-The armature voltage of d.c series generator is not affected by load current. lon winding is mos suitabl for higher voltage rating machin

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 32RQ

See similar textbooks

Similar questions

2- A 4-pole, wave-wound d.c. shunt generator has an armature winding consisting of 300 turns each of 0.0020. The armature resistance is a) 0.152 b)0.62 c) 0.30 d) none of above
1.Two identical shunt generators running in parallel, each with armature resistance of 0.02 ohms and field resistance of 50 ohms. The combined load current is 5000A. The field are so excited that the generated voltages of one machine is 610V and the other is 600V. The terminal voltage of this parallel combination will be. www Ish1 Rh1 a.350-360 V b.450-460 V c. 550-560V Rat www az G₂ Raz 5000 A Ish2
Describe the figures below and how each of figure below are working
Fill in the following blanks:1. Lap winding is suitable for ……. Voltage, …… current d.c. generators.2. The critical resistance of the d.c. generator is the resistance of ……. .
6 shunt generators are running in parallel in a curtain generating station. Each generator supplies a load current of 500 A at 220 V. The shunt field current of each generator is 5 A and the armature resistance of each machine is 0.05 ohm. If one generator is suddenly switched off determine the percentage change in terminal voltage, the total load current being kept uncharged. A: 3%-2%
A) Adding resistive loads in parallel to the output terminals of a series connected DC generator will the total load resistance. a) increase b) decrease c) either "a" or "b" d) neither "a" nor "b" B) Adding resistive loads in parallel to the output terminals of a series connected DC generator will the current through the field winding. a) increase b) decrease c) either "a" or "b" d) neither "a" nor "b"
Out of the following four sources of losses in a dc generator which one is minimum? Copper losses Hysteresis losses Winding losses Eddy current losses
A short shunt compound generator delivers 150A at a terminal voltage is 230V. The shunt field current is 2.5A. The resistances of the armature, series field and diverter are 0.032-ohm, 0.015 ohm and 0.03 ohm, respectively. Calculate the electrical efficiency of the generator at this load.
Please solve this problem step by step and illustrate your answer properly. Write your answer in a piece of paper please. Box the final answer.
A 4 pole generator with wave wound armature has 54 slots each having 28 conductors. The flux per pole is 0.01 Wb. () At what speed must the armature rotate to give an induced EMF of 220V is, (i) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
In a 4 pole, 20 kW, 200 V wave wound DC shunt generator, the current in each parallel path will be
Flashing the field of a direct current generator implies Neutralising residual magnetism Creating residual magnetism by a D.C. source Making the magnetic losses of forces parallel Increasing flux density by adding extra turns of windings on poles