2) Given the following properties of a T-beam: use the 2015 NSCP. Effective flange width, bf = 1200 mm Width of web, bw = 300 mm Effective depth, d 550 mm Flange thickness, t 115 mm Concrete compressive strength, f'e = 23 MPa Steel yield strength, fy = 414 MPa The beam is reinforced for tension only with eight (8) 28 mm bars. Determine the a) balance steel area, b) the ultimate moment capacity of the beam. ANSWERS: a) 8,806 mm? b) 929.7 kN-m

2) Given the following properties of a T-beam: use the 2015 NSCP. Effective flange width, bf = 1200 mm Width of web, bw = 300 mm Effective depth, d 550 mm Flange thickness, t 115 mm Concrete compressive strength, f'e = 23 MPa Steel yield strength, fy = 414 MPa The beam is reinforced for tension only with eight (8) 28 mm bars. Determine the a) balance steel area, b) the ultimate moment capacity of the beam. ANSWERS: a) 8,806 mm? b) 929.7 kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
10. A simply supported beam 300 mm wide, 500 mm deep and spans 5.0 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
Problem: Using WSD & USD, design the midspan reinforcement of stringer (B-3) for the second floor of a 3-storey residential building shown below. Use 20.7MPa compressive strength of concrete @ 28-days and grade 40 reinforcing bars. Use Ye= 24.5 KN/m³. Design the stringer as rectangular beam. Assume simply supported. 450mm 250mm 250mm 450mm, Superimposed Deadloads = 2.70 KPa Stirrups = 10mmo Main bar = 25mm 350mm B-4 STAIRWELL B-1 250x400mm S-3 B-3 250x400mm S-4 (3000) mm 350mm B-4 350mml Stringer Section (2000) mm (3500) mm (2000) mm 700mm
design of singly reinforced concrete beam design the reinforcement. fc' = 28 MPa fy = 414 MPa WD = 4 kN/m (including beam weight) WL = 2 kN/m b=200mm d=400mm length of beam = 5m USE NCSP 2015 specifications. complete assumptions and details. no shortcut. step to step please.
ineed the answer ASAP.ty 3decimal final answer Do not round off in between solution
7.b
The typical T-section results from the monolithic construction of the slab and its supporting beams. The following are the properties based on bending requirements: Effective flange width bf = 648 mm Slab thickness, t = 92 mm Web width, bw = 282 mm Total depth, h = 689 mm Bottom reinforcement = 10 - Ø25 mm Steel cover = 75 mm fc = 25.79 MPa fy = 414 MPa Use unit weight of concrete = 24 kN/m³ Tributary width = 2.5 meter Superimposed dead load = 8.43 kPa Determine the maximum service live load (in kPa) that can be applied on the beam if it spans 7.05 m on simple supports.
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
Q2// A floor system consists ofconcrete slab supported by continuous beam h = 140mm , bw = 300mm,d = 550mm, f 28MPA, fy = with: %3D 420MPа. Determine the steel reinforcement required at mid span of interior beam to resist service dead load moment Ma = 320KN.m and service live load moment M = 250 kN.m %3! %3D 8m + 3m 4 3m 3m 1-1
A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f'c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.