2) For the amplifier below, g,mı = gm2 = 10 mS, Rg = 200 N, Rc = Rg = 5 kn, VA = 00, and B = 100 are given. Assume that both transistors operate in the forward active region, where Vg is a biasing voltage. Draw the small-signal diagram, find the mid- band transimpedance gain expression AR = Vout/lin of the amplifier, and calculate it in dBN. Vc Vcc Rc Q2 VB Q1 oVout RE lin Rs

2) For the amplifier below, g,mı = gm2 = 10 mS, Rg = 200 N, Rc = Rg = 5 kn, VA = 00, and B = 100 are given. Assume that both transistors operate in the forward active region, where Vg is a biasing voltage. Draw the small-signal diagram, find the mid- band transimpedance gain expression AR = Vout/lin of the amplifier, and calculate it in dBN. Vc Vcc Rc Q2 VB Q1 oVout RE lin Rs

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Subject: ELECTRONICS 2
For questions 1 and 2, refer to the VTC of a hypothetical amplifier on the right. Assume the Q-point of the amplifier is set at X. 1. What is the gain of the amplifier at the Q-point? a.) -0.06 V/mV c. 60 V/V b. 5.67 V/V d. -16.67 mV/V 2. What is the maximum peak-to-peak output voltage swing without distortion if the signal being amplified is sinusoidal? c. 120 mV d. -240 mV a. 180 mV b. 240 mV 0.5 IN 65 67 70 mV Vo V 0.2 VI
Thanks
(a) For the given class A power amplifier, determine the following: i. Efficiency of the amplifier circuit for an input voltage that results in an AC base current of 15.44mApeak and DC collector- emitter voltage, VCEQ of 9.15 V. ii. Value of the collector resistor RC using standard resistance value. +20 V 1.2KOS HE+Vo B= 45 10uF (b) Draw the circuit of a Class C power amplifier and compare in detail its advantage and disadvantage from a class A power amplifier.
4) Consider the amplifier shown below with its corresponding small signal model. Using the provided small signal model, perform small signal analysis to determine expressions the you would need to determine Av(s). Do NOT solve for Av(s), just provide the expressions that you would need to determine Av(s). Show your work! Do NOT make any approximations. Vin Cf Vcc WWW R Vo CL Vin W R1 Cf + Vberπ ww R gm Vbe W ro Vo CL
Note: Please do not handwritten.
Quiq plz
on to Electronic Analysis and Design- CE255/EE255 - C courses / Introduction to Electronic Analysis and Design - CE255/EE255 - O1 - Spr The Common Emitter BJT Amplifier has Select one: a. Has a negative gain. b. The input impedance is always very low, whatever the design is. c. The output impedance is always very high, whatever the design is. d. Has a positive gain. e. The gain is always less than 1, whatever the design is. age ssessment CE255/EE255 (O1) - Dr. Mamoun Al-Mistar Jump to...
Please solve a), b) and c) with clear steps.Value of beta =120
Construct an approximate voltage transfer characteristic curve of the amplifier by filling up the table below using the large signal model of the transistor and plotting the results. VI (volts) vo (volts) -2.0 0.0 1.0 2.0 Remarks assume linear transition to saturation transition to cut-off assume cut-off VI 2.5 V 100 K Ţ Vo
B. Make a sketch of the channel region when VGS=VGS-OFF and make a sketch of the channel region when ID=IDSS and explain why each channel has this shape. C. Assuming that the measured values for the PF5102 were VGS-OFF= -1V and IDSs 10mA, design a common source amplifier for ID=4mA and VDS= 4V using a 12V supply and combination biasing without degeneration as you did in the laboratory. D. Find the input resistance, output resistance, and voltage amplification of your design using the hybrid-pi model and explain how you measured these parameters in the laboratory.
Problem #5 Use the following process parameters Tox = 9.10 "m, 4, = 350.10 m /V-S1.V= 0.7V,Y = 0.45 For the amplifier shown below, assume A-0 (a) What is the small-signal gain if M, is in saturation with lo 1mA? (b) Compute the value of input voltage and the small signal gain when M, is at the edge of triode region (c) Compute the value of input voltage and small signal gain when M, is pushed further into triode region by 50mV 3V 2kQ VOUT VIN M,(50/0.5)