2- Design a tie column to cary an axial dead load of 600 kN and an axial live load of (1.6X1+2.6X2) kN. Given material properties are fy= X2 MPa, fc=X¡ MPa A=? b=? h=?

Q: 3- What size of threaded rod is required for member AB given in figure below. The applied load of X2…

A: Consider the following diagram of the threaded rod. Calculate the angle. tanθ=2.74.5θ=30.96∘

Q: 92

A: Consider beam AC

Q: Q2. Figure 2 represents part of roofing system where the point loads of X2 kN are applied according…

A:

Q: Treat the trapezoidal region as a composite of a rectangle and a triangle to find: a. Find X bar…

A: It is required to find the centroid and moment of inertia.

Q: D A cylindrical tank with its axis vertical gas a diameter of 2 m and a depth of 8 m. A standard…

A:

Q: Problem I. In a road construction along the CaviteX expressway, a wedge of weight (W; =552 N) is…

A:

Q: We make a cut through BC, BF, and FG. The free-body diagram of the section to the left of the cut is…

A: It is asked to calculate force in member BF.

Q: If D kN and E kg, calculate the resultant of the two applied forces in pounds and its direction from…

A:

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assume a = 310 mm, b = 570…

A:

Q: 2. Locate the centroid (x, y) of the cross-sectional area. 5 in 05i 0.6

A:

Q: Question 1 The reduced level at the intersection of a rising gradient of P % and a falling gradient…

A:

Q: 11. In figure 6, compute the pressure difference between m and n, in pounds per square inch, when:…

A: The given data is shown below: Sp gr of brine=1.15Sp gr of oil=0.92z=100 in.

Q: y(V) – y = 0 1. y" – 10y' + 29y = 0 2. %3D

A:

Q: Locate the centroid x and y of the cross sectional area of the angle bar

A: Given:- An angle bar is shown  To determine:- The centroid x and y of the cross-sectional area of…

Q: Determine the x. Measure it from the y-axis. 90 mm -70 mm- 60 mm 60 mm 40 mm -120 mm

A: To find the centroid -

Q: 3 Using the parallel axis theorem, determine the moment of inertia about the xxis for the same shape…

A:

Q: 4. Find the location (x, ỹ) of the centroid of the following shape using the origin given. 55 mm 45…

A:

Q: Plot the given pair of points on a Cartesian plane, draw a straight line between them and determine…

A: Subpart 1: The following figure shows the points in Cartesian Plane and the straight line connecting…

Q: A cable was used to dry the clothes from wet laundry by hanging as shown below. The clothes are…

A:

Q: Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of…

A:

Q: Q5. (P.) A 30 m height slope is to be built as shown below. The homogeneous with c' = X kN/m² and o'…

A: Given:  C'=X=35KN/m2 ϕ'=Y=30°γsat=Z=19.5KN/m3Yw=10KN/m3F.Scheck=2 Radius of Arc = 30m   To Find: The…

Q: P 1 m W = X N 1 ms = 0.4 5. Determine the normal force between the crate and the surface 6.…

A:

Q: 5 in. 1 8 in. R = 6 in. 2 in.- y H (a)

A:

Q: Discuss how the steel structure will contribute to sustainable development. Include the discussion…

A: Steel has a high recycling capability, which results in less waste, energy consumption, and…

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

A:

Q: For square shape, the centroids values in X and Y directions are equal, while the centroid of circle…

A: The centroid refers to the point where the whole area of the object is assumed to be concentrated.…

Q: V' B D. H F G W W Z' 6 @ X' = Y' Z'

A: Solution:- Support reaction at A and E Taking moment about C from left end and right end…

Q: Determine the force in each member of the truss A 60° B -Am -Am- -Am 60 D YkN

A:

Q: Derive an expression of the maximum statical moment of area, Q and its location from the given…

A:

Q: Topic: Deflection of Beams (Geometric Methods) Area Moment and Conjugate Beam Situation #1 El is…

A: X = 192 kN and Y = 93 kNRequired:Deviation of B with respect to tangent at ADeviation of A with…

Q: Page |4 QUESTION 4: Determine the reactions at A and B for the beam with an overhang and a…

A: Take moment about B∑ MB=0RA3-151.5+1212.523×1.5=0RA≈4.5kN

Q: 3? (KIN) GF? (kN) What is the force in member What is the force in member FE? (kN) What is the force…

A:

Q: Determine the force in each member of the truss

A: ∑MG=0-HA×4 + 5×2 + 94×4 + 212×6=0HA=414.5 kN →∑H=0HA-HG=0414.5-HG=0HG=414.5 kN…

Q: Angle: 34.9 Start point x: -9.7 y: -6.2 End point x: -3.1 y: -1.6

A:

Q: Y

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.