2) Consider the multi-stage amplifier shown below. Determine Vin if Vo = 3.3V. Because ₂ is so small and le2 is so large, do NOT assume that Ib=0 and do NOT assume that I le Assume that both transistors are in Forward Active and each is described as follows: Q1: B₁ = 100, VBE(ON) = 0.7V Q2: B₂ = 14,VBE (ON) = 0.7V 10V Vin 10V T 2K Q1 500 V01 Q2 220 Vo

2) Consider the multi-stage amplifier shown below. Determine Vin if Vo = 3.3V. Because ₂ is so small and le2 is so large, do NOT assume that Ib=0 and do NOT assume that I le Assume that both transistors are in Forward Active and each is described as follows: Q1: B₁ = 100, VBE(ON) = 0.7V Q2: B₂ = 14,VBE (ON) = 0.7V 10V Vin 10V T 2K Q1 500 V01 Q2 220 Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6) the "simplest" model of transistor behavior in this problem, i.e., B = o and IB = 0, with forward bias voltage of AVBE = 0.6V. Consider the following circuit with a transistor and two resistors. You may use 5V a) Determine the output when Vin = 0.5V. 9kN Vout Vin 3002 3kN b) Determine the output when Vin = 1.2 V. c) Determine the output when Vin = 3.6 V.
choose the correct answer 33
B= infinity, Assume BJTs are identical. Find R such that a DC current of 0.25mA for transistors Q1 and 2. Find Rc that results in 3V DC at he collectors of Q1 and 2. Find the differential voltage gain.
Since the transistors used in the circuit are b=200 and r0= ∞(endless);A) By analyzing the DC for each amplifier floor separatelyre1, re2 find resistance values.B) Draw the AC equivalent circuit of the amplifier circuit.C) For each floor Zi=?, Z0 =?D) For each amplifier floor Av1, Av2 find the tension gains.E) Avl find Vl voltage value by finding voltage gain.
For the circuit in Figure 1, the transistor is biased so that ICQ is 10 mA and VCEQ is 8 V. As a starting point, let VRE be 20% of VCC. Calculate the values needed for RE and RC.Assume β is 100. Select the nearest standard values for the twoCalculate the values of R1 and R2
estion 2: Consider the BJT circuit given here. ( Write the input and output loop equations For the given values of Vcc= 10 V, Vin = 4V and resistor values, calculate all current values (IB, IC and IE) and VCE Assume that the ß for the transistor is 100 and the voltage drop across LED connected between Collector terminal and resistor (Rc) 2.1 V. TH i. ii. 111. VIN Vcc Rg=100 kΩ Re=2 kΩ LED 2.1 V B= 100 Based on the above analysis, correctly identify the current mode of operation Cutoff mode Active linear mode Saturation mode
Use 2 decimal places A CS JFET amplifier has gm= 6.82 mS, with a drain resistance of 1.13 kohms and load resistance of 685.52 ohms. Voltage gain (absolute value) is Round your answer to 2 decimal places.
To operate as an amplifier, it is the base of an npn transistor... Please select one: a. 0V b. positive by collector c. negative relative to emitter d. positive relative to emitter
Figure 2. illustrates a transistor amplifier implemented with a transistor (we can use PN2222 data here) and two resistors, which receives the operating voltage from a 10 V voltage source. Current gain of the npn- transistor ß=hFE = 100. Calculate a) base current IB b) collector current, Ic c) collector-emitter-voltage UCE d) determine in which state the transistor is operating (saturation, cut off, active) RB IB Rc Ic +il+ Vcc Figure 2. Npn - transistor connection. RB-300 kn, Rc-2k2, Vcc= 10 V.
In an emitter-biased transistor circuit, we have collector source voltage V CC = 15 V, collector resistance RC = 3.5 kOhm, emitter voltage V_E = 4.3 V and emitter current LE = 2.1 mA. If the current gain is 150, what is the difference in emitter-collector voltage V_CE when we calculate it including the gain factor vs when it is calculated by assuming collector current LC = LE? Select one: O a. 3.35 V O b. 3.40 V OC 0.05 V O dov
1.
Complete the given BJT circuit. Solve for the value of the resistors and the voltage supply that will satisfy the given DC loadline. Assume IC=IE and RC=RE. Show and label properly the required final circuit. 5 mA 2.5 mA * IC IC 0 15 V 30V VCE RB B +VCC C E RC B=100 RE ...