2-31 Find REQ in Figure P2-31 when the switch is open. Repeat when the switch is closed. 100 Ω REQ -WWW 50 Ω www 100 Ω FIGURE P2-31 100 Ω

Q: *Experiment No. 6: Comparator Circuit 1-.What is the pin number of the IC comparator output signal…

A:

Q: Draw the following signal 3-3e-t/3 Please upload picure of your graph.

A: The given signal is x(t) = 3 - 3e-t/3 You can plot the signal by substituting different values of t.

Q: There are many different matching techniques. What are important factors required to select a…

A: Thre are different matching techniques however they all have certain important factors required to…

Q: Q14: The arithmetic shifts right instruction ashr means divide the number by 2. Find the result of…

A: First 08 is loaded into the Acummulator in the form of binary. Given that ashr means divide the…

Q: Design a circuit and write an Arduino code to displays "5 seconds elapsed" and blink an LED every 5…

A: It is asked to design a circuit and write an Arduino code to displays "5 seconds elapsed" and blink…

Q: Identify the component which is not available in digital Voltmeter? a. Clock generator b. ADC c.…

A: We need to select component which is not inside the digital voltmeter .

Q: Example of solving series and parallel, parallel connections and measurement devices

A: Series connection  Voltage across the components will vary based on types and magnitude of…

Q: Define the following: 1. Color Rendering Index (CRI). 2. Ingress .Protection. 3. Illuminance

A:

Q: Consider a 8-bit ADC and full scale voltage measurement range of (-29 to 29).The Resolution  will be…

A:

Q: QUESTION 29 Select all signals that are inputs for the 8088. Use the schematic for our board. OSC…

A: Consider the schematics of 8088 shown below,

Q: lect all correct answers. elect one or more: Da The figure consists of 2 loops. Ob. The figure…

A: to select one or more correct answers a) the figure consists of 2 loops b) the figure consists of 1…

Q: List the different types of Q-point stabilisation techniques and explain any one technique. Find Ico…

A: We need to list the different types of Q-point stabilization techniques and explain any one…

Q: 1. Observe the physical parts of the analog trainer   2. From your observation list down the major…

A: Electrical devices are used for measuring electrical parameters. Current, voltage and power are…

Q: You are required to calibrate a Temperature transmitter for process control using a provided…

A: A temperature transmitter is used to convert the output of a temperature sensor into a measurable…

Q: Crystal radio receiver Please explain how this circuit works

A: NOTE- According to the policy, we can answer only one question, please post other question as…

Q: How JFET manages to be operable when it doesn’t need biasing current

A: Junction field-effect transistors are the most basic type of field-effect transistor (JFET). They're…

Q: Assume that carry flag is 1 at the beginning, and execute the following code: mov al, OE8H rcl al, 1…

A:

Q: represents a circuit breaker with thermal overload protection? A. C B. D C. A D. B

A:

Q: 2. Identify each device. (a) 74LS157 (ь) 74LS151

A: According to the context of the given question, it is only required to identify the given ICs in the…

Q: Need solution within 15 mins. Give 5 stars for correct solution

A: The solution is provided in the following section:

Q: Propagation delay is usually measured in O a. milli-volts O b. nano-seconds O c. nano-Watts O d.…

A: We need to tell about unit of propagation delay

Q: Q1 A. Draw the interface of an 82C55 PIA controlling two digits of 7- Segment display and reads from…

A: According to the question, we need to draw the diagram for the interface of an 82C55 PIA controlling…

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: Horizontal Controls Autoset tical Controls Trigger Controls

A:

Q: Explain in detail what happened to the current and voltage measurements as S1 and S2 (2nd pic…

A: Set 1 (S1) and Set 2 (S2) are switched places. The tables are as shown below,

Q: mention at least three practical application where,ASK,FSK and PSK techniques are used. Subject is…

A: ASK, FSK and PSK are types of digital modulation techniques, digital modulation techniques have…

Q: HW14/ H.W: control the intensity of the LED by serial.

A: We required the following elements for the following to control the LED Arduino Board Led Arduino…

Q: Thank you that helped a lot but In which part of the drawn circuit are inputs??

A: Given sequence is an irregular counter sequence . In the given sequential circuit for the given…

Q: The names of the companies that use the pulse: the signal processor in the manufacture of electronic…

A: Please find your answer below

Q: Explain the purpose of the switch debouncer and how it functions?

A: Switch debouncer: Mechanical switches are a typical component in manual control circuits in both…

Q: A conveyor motor has a N.O. START button (I:0/3) and a N.C. STOP button (I:0/4) to start and run the…

A: To draw the program rungs for given operation

Q: Question 1 A microcontroller is used to control three LEDS in series (Blue, Red and White). Assume…

A: Here, we have asked to design an interfacing circuit to control three LEDs connected in series,…

Q: What are CT and PT?

A: In This Question, It is asking about CT and PT. CT stands for Current Transformer, and PT stands for…

Q: 1) Given the figure and values below: R = 5.6 kfl , Rc = 4.7 kil , Rg = 1.2 kfl, Vcc = 18 V, Vc = 12…

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.