2- 23

Q: Locate the centroid y of the shaded ared. L=23.6mm y 2L L 2L 2L

A:

Q: Use the cutting planes shown to draw the sectional views.

A: The sectional view of the above figure or diagram is shown in the below step :

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: 120N 80N 300

A:

Q: 1-2in. -1in-+1int Hin 3in- T 3in 2in

A:

Q: Draw the top, the front, and the right-side orthographic views of the objects shown. Indicate when…

A: The orthogonal projection is the projection of the three-dimension object into the two-dimension in…

Q: 150 mm Locate the centroid of the coloured area. 50 mm 100 mm 100 mm

A: Marking points over figure- A, B, C, D, E, F In the fig three shapes can be observed clearly- 1.…

Q: How many centimeters long is side AC?

A:

Q: Given the multiview projection of the solid, draw its isometric view.

A: Solution- The given diagram is shown below. To Determine,  The isometric view

Q: 6. Draw a true distance between a point Q and a plane B. Vs he 7. Draw a piercing point and…

A:

Q: one help please can you help me to draw an isometric view of the bridge (truss)

A:

Q: Hinge TT Determine the degree of indeterminacy (i) of the frame shown.

A:

Q: Draw the isometric perspective and the ortogrophic views of the object (4 views in total). Indicate…

A: Solution:- The Isometric & Other 3 Views of the figure are mentioned below with the Dimension.

Q: DRAW HE FREE BODY DIAGRAM wooDa FLANK BOX 5K6.

A: To draw the free body diagram of the given box.   The purpose of a free body diagram is to represent…

Q: Locate the centroid of the plane area shown.

A: Given: r1=72 mmr2=120 mm To find: Centroid of plane area.

Q: Find the length of side TS.

A: Consider the figure,

Q: Draw the front and the right side view of the given machinery part.

A: (Not drawn to the scale)   Front View:

Q: 50. Complete an interpretation drawing that shows the permitted angularity tolerance zone. 200 A 62…

A:

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: What is Dutch (Deft) cone is consists of?

A: The cone penetration test (CPT) is a technique used to measure the geophysical characteristics of…

Q: Which of the figures on the left is unstable? (1st or 2nd or both) DB

A: Two figures are given as shown in the figure above and it is asked in the question whether these…

Q: Produce the section view of the object (a) as shown by the section plane (b). b

A:

Q: In the given sketch design any of the two way slab panels. 10x21 18x12 26x12

A: Condition for two way slab l/b<2   d (effective depth) = D (overall depth) - clear cover - 1/2…

Q: 40" -45"-

A:

Q: TOP VIEW 130 R30 STILLST R30 20 3X 024 65 FRONT VIEW -R30 1242- LL Ø16 R22 44 RIGHT SIDE VIEW

A:

Q: D O00 15KN 15KN B.

A: Given data : Number of member (m)=13Number of external support reaction (R)=2+1=3Number of joint…

Q: Hinge What is the degree of indeterminacy (i) of the frame shov

A:

Q: 16-11.828⁰ 9-2 9-5.828¹ 10.342 8x8 POST PIO 12-11.342* 6-5.143* TT 8x12 RAFTER P109 8x8 POST P102…

A: free body diagram of the bottom chord

Q: d²y ¸ dy + 7. - бу 3D 36х dx² dx

A:

Q: b (x+c)(x-c) A

A: To solve the expression (x+c)(x-c) step by step, we'll use the difference of squares…

Q: draw the front view, side view, and top view of these two figures.

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: 33. Draw three views of the shalt guide. 22 -55 57 30 20R 15- 22 45 -85- 40 Bore 70-- PROB. 33…

A: We can represent any 3D figure in 2D by 3 views  Top view  Front view  Right / Left side view

Q: What is the slant distance of the centroid of the gate (y)? 2 m measured from A 3 m measured from C…

A: We have to determine the slant diatance of the centroid of the gate ( y^bar ) which can be from…

Q: Date: 1 1 2m² for the turss Shown determi the forces in mebers BCA Hland Gl 30010 التاريخ : I H…

A: To find force in member BC,BI,GI

Q: Convert 3el12 to rectangular form.

A: The polar form of a complex number is given as

Q: 6kN 2 kN\m 3 kN D 6kNm A B A CA 6m

A:

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.