2-122. Determine the magnitudes of the components of F acting along and perpendicular to segment BC of the pipe assembly. Prob. 2-122/123 4 ft 3 ft N F = {30i - 45j + 50k} lb MOONDAY A C 4 ft B 4 ft 2 ft

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E=29 000ksi). If the end C is…

A: Given, E = 29000ksi, Vertical displacement at point c, (yc) = 0.75in FBD :-

Q: F2-7. Resolve each force acting on the post into its x and y components. F₂ = 450 N 45° y F₁ = 300 N…

A: Given Load 300 , 450 and 600 NAngle 45 ° To find out X and Y components

Q: Determine the height and the following reactions of the cable

A: Given: To find: The height and the support reactions of the cable

Q: Determine the internal shear in kip at the distance 14 ft. from point A (it is the point between…

A:

Q: Cables AB and BC are tied to the ring at B. Find W, and W, knowing the barrel weighs 450. Ignore the…

A: Given :

Q: 2. The pipe assembly is subjected to the force of F = (600i + 800j - 300k) N. Determine the moment…

A:

Q: 30KN 30KN 30KN В 15KN >15KN 30deg30deg A 30deg 30deg

A: Ft

Q: Determine support reaction

A: Introduction : The given beam is a cantilever beam . It contain one point load , one moment and one…

Q: Q2. Draw the influence line for (Rb, Rc, Rf, Rg, Mp, Mm, and Mb) m A B C D E F G mmm b mom n mmm b.…

A: Step 1: Step 2: Step 3: Step 4:

Q: Problem 4 - Two homogeneous rods ABCD and BE are bent as shown and rigidly connected to each other…

A: Two homogeneous Rods are given as shown in the image above and it has been asked in the question to…

Q: The 40-kg homogeneous plate is suspended from three cables. Determine the tension in cables at A, B…

A:

Q: ipe. use mohr's circle

A:

Q: 18.0

A:

Q: *4-32. The pipe assembly is subjected to the force of F = (6001 + 800j – 500k) N. Determine the…

A:

Q: Find all forces i member AB,BD,DE

A: given:

Q: A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is…

A:

Q: Ex! 2 Design a round spiral Glumn to support on axial dead lod Polof 1090KN and an oxial live load…

A: Spiral column reinforcement : Diameter : i) 14*ϕLL ii) 6 mm Take maximum of above  ϕLL is the…

Q: Q4-A) Gate AB is 1.2 m long and 0.8 m into the paper. Compute the force F on the gate and its center…

A: Compute the force F on the gate and its center of pressure,X

Q: 11-7. The supports only exert vertical forces on the beam. Determine the greatest magnitude of P…

A:

Q: Determine the horizontal component of the total hydrostatic force (kN) acting on the curved surface.…

A:

Q: 100 kN Find the horizontal base reactions for the portal frame shown, when the vertical bars have A…

A:

Q: 15 KN LL B F 10m 5m D A 10 m 10m E 40 KN G U x5mx O 4m * 6m 10m

A:

Q: Problem #1 Beam ABCD has an internal hinge at C and rollers at B and D. Draw the lokip necessary…

A:

Q: nember AD, BC, CD and BD. 20KN 4m A B 4m 30KN 4m C O E 4m 3m FX 6m

A:

Q: tensions in cables AB, AC, and AD.

A: Lami's Theorem- If three coplanar forces acting at a point be in equilibrium, then each force is…

Q: 10kN kN 10 5kNm m EI B Зт 1m 1т

A:

Q: Please provide a detailed solution especiallyl for the moment of inertia and how you got the values…

A: Dimensions from the Image (refer to your image for confirmation):b (flange width): 40 mmh (total…

Q: N 60 lb 50 lb 12" 10" -15" Problem 2 Figure 40 lb-ft

A: Resultant force =

Q: ») Figure Q3(b) shows a concrete corbel structure, fixed rigidly to a wall support. It is subjected…

A:

Q: F2-20. Determine the length of the rod and the poxition vector dirceted from A to B. What is the…

A: The position of points in the problem is as; A= 4i + 0j + 0k B = 0i + 2j + 4k Vector (AB) = (Vector…

Q: Determine the distance y̅ to the center of gravity of the homogeneous rod.

A: Given: Height of the cable = 2 m Width = 1 m.

Q: NEED IN 1HOUR PLS THANKS From the figure, compute for the horizontal and vertical component forces…

A: To find horizontal and vertical component forces of the hinge at B acting upon member AC

Q: Determine the axial force in member DA KN.0

A:

Q: Determine the reactions at Pin A, Rocker B and Pin C Note that piece ACF and BCDE are each one…

A:

Q: Determine the angle θ between the pipe segments BA and BC.

A: First, we draw the free body diagram:-

Q: The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E - 29,000 ksi;…

A: Given, E = 29000 ksi I = 843 in4  w = 6.7 kip/ft or 0.558 kip/in

Q: -12'- C H V 12'. G D 12'. TI F

A:

Q: he support bracket for a water pipe that brings water from the city water system into the basement…

A: The pressure force is defined as the force that is exerted by the pressure on any area that is equal…

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.