2 07. The standard time for a job is 10 hours, hourly rate is Rs. 10. A worker completes the job in 8 hours. Calculate tthe bon earned by the worker in Rs. according to Hasley plan. ps: A. O 10 B. 08 C O12

Q: What is the example of a device undergoing transient (rather than steady-state) operation? Group of…

A: following are the explanations for the above heat transfer cases-

Q: known that a vertical force of 200 I C from the board. As the nail first st ment about B of the…

A:

Q: 7-11. The overhang beam is subjected to the uniform distributed load having an intensity of w = 50…

A:

Q: 2- Plumb line is held steady while being carried along in a moving train. If the mass of the plumb…

A:

Q: The electronic throttle control of a model train is programmed so that the train speed varies with…

A: The Answer is below

Q: The acceleration of a particle is given by a = 3t-30, where a is in meters per second squared and t…

A:

Q: No need of Explanation Just Show it.

A: Given Contour of an aircraft To find Stagnation point High pressure  Low pressure

Q: The calorific value of a hydrocarbon fuel used in a tubular can-type combustor is 42000 kJ/kg. The…

A: Given, CV = 42000 kJ/Kg V = 75 m/sec = 246.063 ft/sec P = 55 kPa T = 350 K = 630 R V= MγRgcT M =…

Q: Explanation need. Fast

A: 1. Iso-thermal - Expansion. A thermodynamic process known as an isothermal process occurs when the…

Q: An axial pump that delivers 15 gpm, has a volumetric efficiency is 93%. Find its theoretical flow…

A:

Q: The shear force at x = 1 m is.......KN.

A:

Q: Q2b) The supporting wheel on a scaffold is held in place on a leg using a 6 mm diameter pin as…

A:

Q: The bobcat loader (Figure Q3) has a mass of 1200-kg, shows the center of mass is at G1. If there is…

A:

Q: 6-84E A heat engine is operating on a Carnot cycle and has a thermal efficiency of 75 percent. The…

A:

Q: humidity ra T is represe ectiveness is erson with

A: introduction: here we have to correct the above statement

Q: 4. For the mechanism in the next figure, OA = r , OB = d and the angle between BO and OA is . a)…

A: To solve this problem, we need to apply the cosine law of triable to determine the length of AB.…

Q: Q2/ An ideal gas, Cp= (2) R and Cv=R, undergoes the following mechanically reversible changes in…

A:

Q: The forces F1,F2 and F3, all of which act on point A of the bracket, are specified in three…

A:

Q: On a highway at night, while you are driving very fast with a speed of 160 km/h you notice a stall…

A: Givenu=160 km/h=160×518=44.444 m/ss=80m

Q: In a tensile test, initial length of the experimental specimen is the final length of the specimen.

A: we have to determine the effect of tensile test on the length of specimen

Q: A 20 kg mass attached to the lower end of a spring whose upper end is fixed, vibrates with a natural…

A: this answer is given below.......................... all of my  answers are correct but this answers…

Q: 1- Determine the moment of the force about point O. Neglect th thickness of the member. 500 N 300 N…

A: Given

Q: Resolve the 20N force in Fig (2), into components along the a and b axes and determine the magnitude…

A:

Q: The square plate is confined within the slots at A and B as shown in (Figure 1). When = 40°, point A…

A: To findDetermine the magnitude of the velocity of point C at this instant.Determine the direction…

Q: 12.17 Boxes A and B are at rest on a conveyor belt that is initially at rest. The belt is suddenly…

A:

Q: A linear actuator is connected to link AB at location A. The linear actuator is extending with…

A: GivenVa=9m/saa=-10m/s2

Q: 4. For the frame and loading shown, determine the reactions at A and F when (a) a = 2 in., (b) a =…

A: To find: (a) For a = 2 in. Reactions at A, Ax = ? , Ay = ? Reaction at E, RE = ? (b) For a = 7.5 in.…

Q: If the mass of cylinder A is 40 kg. determine the mass of cylinder C in order to hold the assembly…

A:

Q: infinitely long pin fin,

A: SQRT( 2) IS THE ANSWER

Q: E : Consider a large plan wall of thickness L=0.06 m and thermal conductivity k-1.2 W/m °C in space.…

A: Given that ε=0.85 , solar absorptivity(α)=0.26 T1=300K  ,  L=0.06m  ,  k=1.2  , qsolar=800W/m2 outer…

Q: Question 1: For the following truss structure (with members AB, BC, AD, DE, BE, CF and FG all of 60…

A:

Q: Determine the torque T that can be applied to the rectangular tube as shown in figure(5),if the…

A: To find: The torque T that can be applied to the rectangular tube. Given data: The average shear…

Q: 3: open loop transfer function a unity feedback control system is G(s) = the i S(1+TS) o the system…

A:

Q: M 2.2 kW Domestic Hot Water H 1.7 kW

A: this is long process  i solved this problem earliar believe me  answer is option c  0.111kg/s if you…

Q: Which of these statements is true? a. A force applied on a rigid body can be freely moved to any…

A: A force and a coupled is applied on the rigid body. We have to choose the correct statement for the…

Q: Q3/ A 10-cm length of platinum wire 0.5 mm in diameter is placed horizontally in a container of air…

A:

Q: Rank the following pipe sections according to their loss coefficients. (Place the section with the…

A:

Q: the two forces applied at A is to be vertical, (b) the corresponding magnitude ofR. A) A steel tank…

A:

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm  D=41mmPCD=63mm

Q: standard reference of water content determination is ASTM D 2216 True False flat grooving tool is an…

A: Solution.jpg

Q: of The y-coordinate of a particle in curvilinear motion is given by y = 4t³ - 3t where y is in…

A:

Q: The scale of an aerial photograph is 1:15,000, In the photo you measure the length of a bridge to be…

A: Given data: Scale=1:15,000L=0.25 in Need to determine the length of the bridge in feet.

Q: Determine the resultant moment produced by forces FB and F pout point O. Express the result as a…

A:

Q: 1. What is the enthalpy of saturated steam (water) at 20°C and 73°F in both kJ/kg and BTU/lbm?

A: