(1e:2.13) An impedance Z is built from a resistor and capacitor connected in parallel. When connected to an AC voltage source with a frequency off 60Hz, the impedance has a numerical 1000 (1-j). The impedance is connected as shown in Figure 2.21, where the value of Z= voltage source has an amplitude of 10 V. At t=0, the AC voltage is at a maximum. (a) What are the values of R and C? -- (c) What is the current in the resistor, in(t)? (d) What is the current in the capacitor, to(t)?

Q: Derive current divider rule formula

A: The solution can be achieved as follows.

Q: Discuss the concept of block diagrams and how they are used to represent system models.

A: We have to discuss the concept of block diagram and how they are used to represent system model.

Q: B / Name for application for power electronics science?

A: Power electronics science is the field of study that deals with the effective static control,…

Q: ripple counter“

A: Counter- A device used for counting binary numbers is termed as digital binary counter. Digital…

Q: Why is electronics important?

A: Electronic devices have become an indispensable part of our daily lives. It is becoming increasingly…

Q: Define circuit breaker and write any two types

A: Circuit Breaker - Circuit breakers are mechanical switching equipment that may individually or…

Q: Discuss whether NEC provides the maximum requirements or minimum requirements.

A: NEC is the acronym of National Electrical Code.

Q: - Explain briefly the basic ways adopted to execute a power security analysis.

A: The power security analysis  is executed in two ways; 1) Security assessment: - The previous gives…

Q: ketch the following for the device which uses pulse gate signals to turn ON and turn OFF process.…

A: Simple question based on the subject ,power electronics. In this we are finding the cross sectional…

Q: 1. a) What ao the areas of the circuit labeled "A", "B“, and" C" do? b) Explain the operation of the…

A:

Q: Q.3 For Resistance temperature detectors (RTDS) I) What's the principle of operation for Resistance…

A:

Q: Describe ring counters in detail and how they are used.

A:

Q: Enumerate and define the classification of electronic communication

A: Communication is the way of expressing the thoughts in the form of messages from one end to the…

Q: What are the uses of multi electronic devices?

A: Few multi electronics uses are discussed as follows: Invertors: Investors have many electronic…

Q: Explain the steps for chip mounting.

A: Chip mounters are required for the mass manufacture of consumer and other electronic products…

Q: What is common channel signaling? And how does it work?

A: Common channel signalling  It is signalling in which a group of voice and data channels share a…

Q: SCR is a three layered three junction power electronic switch? a.True b. False

A:

Q: Explain with necessary block diagram how a circuit breaker can be effectively controlled by using a…

A: A circuit breaker is the operated automatically type electrical switch to protect the electrical…

Q: What is biomedical Instrumentation explain with examples

A: Biomedical Instruments  Bio-Medical Instruments is the application of knowledge and technology to…

Q: Punch Trough IGBTs have........... voltage blocking capabilities.

A: The IGBT is insulated-gate bipolar transistor. Based on structure the IGBT classified as, Punch…

Q: What is analogue signal?

A: The analogue signal is continuous in nature and it represents both time and amplitude.

Q: Explain and draw an NPN transistor chip in a circuit of your own design. I want the actual chips…

A: An NPN transistor has three terminals: the emitter (E), the base (B), and the collector (C). In an…

Q: c) Electronics engineering defines a broad field that encompasses many subfields including those…

A: To interpret the cardinal role of electronics engineer

Q: How does a transistor compare to a physical switch in a digital circuit? Use illustrations.

A: As we know that transistor works as a switch in saturation region or in cutoff region. Cutoff region…

Q: Define Digital

A: In the context of electrical engineering, Digital is a type of signal which is active at only…

Q: Explain the and troth table ? ) Full adder circuit

A: Full Adder A full adder is a combinational circuit that takes three inputs, performs an addition…

Q: What is a snubber circuit? Name some uses also

A: A snubber circuit is an electronic circuit that is commonly used in power electronics to protect…

Q: a) Explain the operational concept of the components below that is included in a…

A:

Q: In the voltage-controlled square/triangular waveform generator circuit we covered, is the transistor…

A: As the circuit is not given it is difficult to understand the situation exactly. I will assume that…

Q: How exactly does one go about clearing an EPROM for the very first time?

A: EPROMs (Erasable Programmable Read-Only Memory) are non-volatile memory devices that can be…

Q: what are the kinds of circuit that can control the bass/treble in an audio system. with some…

A: In an audio system,tone control circuits attenuates the low or high frequency of the input…

Q: What role does environmental testing play in assessing the reliability of electronic components

A:

Q: Give the reason for the following statements: 1) Using a Venturi flow sensor makes the measurement…

A: Any liquid coulmn upto a certain height has some potential energy. Venturi flow meters are devices…

Q: 1. Define the following about Systems:  a. What is used to describe or determine a black box…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.