185 kPa and 450 K, resp=

Q: Starting with the general linear momentum balance Dr M p v dv = ₁ SS Dt V A F DA + S ● b consider a…

A:

Q: Briefly define Scrum project methodology

A: For a small team scrum project methodology is a management methodology which is leaded by the scrum…

Q: Select three games of your choice and analyze the subverting conventions that are applied in these…

A: In conclusion, the graphic designs of The Stanley Parable, Undertale, and Journey all challenge…

Q: INSTRUCTIONS: 1. CREATE YOUR OWN 2D MODEL(i.e. flower pot, flower base, water jug) 2. MAKE A 3D…

A: Given question: Create a 2D model of a flow pot, flower base or water jug Make a 3D drawing from…

Q: Draw the top, the front, and the right-side orthographic views of the objects shown. Indicate when…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q: Question and needed info below. Thank you in advance

A: The Front view of above given BASE object,

Q: General definition of the concept of virtual engineering (VE), including the main four key aspects…

A: Virtual engineering is integrating geometric models and engineering tools such as analysis,…

Q: John Wick once again finds himself outnumbered, outgunned, and injured, and is running for his life…

A: John's weight (Wj) = 185 lbsLoad weight (Wl) = 500 lbsLarge double pulley weight (Wp) = 100 lbsOuter…

Q: Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it…

A: Dear student,Part 1: Answer:(i) The given dynamical system can be rewritten as a single second-order…

Q: You've used pens and mechanical pencils for years. Check out five pens and mechanical pencils.…

A: It is asked to write about 5 pens and pencils

Q: A cylinder with radius R moves in an incompressible ideal fluid at a velocity perpendicular to its…

A:

Q: analyzing a process with an average processing time of 1 minute and an interarrival time of 10…

A:

Q: In turbulent flow over a smooth bed, the flow is typically separated into two regions. Near the…

A:

Q: Q. 8.) ZV=0 RA+RI = L0+20 +20+20 20+20 +20+20十 ZMA=0 20x3 +2OX6+20x9+20x12. +20 X 1S +20x18+20x21…

A:

Q: Enlist the parameters that influences the B.E.P and explain how these parameters will influences it…

A: The break-even point and a useful tool for the study of the relationship between the fixed cost and…

Q: Write a Technical report of BRT project in your own words.

A: Bus rapid transit, also called a busway or transitway, is a bus-based public transport system…

Q: 10. Eric bought a brand new truck in July and was really excited to drive it. Vehicle maintenance is…

A: When hot summer July  the pressure inside the tyre is P=35 psi But when measured  in January the…

Q: Write a pragaraph about Manufacturing Engineering ,negatives and positives

A: all Coin have a two side, like wise manufacturing Engineering also hase some pros and cons which is…

Q: you know how a company may protect itse

A: Ways to protect account data from hackers. Hackers find weaknesses in computer systems or networks…

Q: Question 3. (i) The equation of hydrostatic equilibrium for a region of fluid, enclosed by a surface…

A: Introduction:The concept of hydrostatic equilibrium is particularly important as it describes the…

Q: Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it…

A: Step 1:Step 2: Step 3: Step 4:

Q: Select one: a. Running an NC part program without touching the stock. Ob. The first time that a new…

A: introduction; A dry run is used for testing of machine program by cutting of air.

Q: t in an organic synthesis, orarily stored in drums fo

A: The management approach helps to understand management. There are many approaches to management that…

Q: First Printing and Copy Center has 4 more jobs to be scheduled, in addition to those shown in…

A: Given:First Printing and Copy Center has 4 more jobs tobe scheduled, in addition to those shown in…

Q: Describe the advantages of designing an object using 3D software instead of 2D software.

A: we have to discuss the advantages of using 3D Modelling over 2D

Q: Scenario B: Figure 2 shows part of an automatic screwdriver designed to drive several million…

A:

Q: An air conditioning unit uses Freon (R-22) to adapt an office room at temperature 25 oC in the…

A: The data given in the problem is, Temperature at condenser, T1 = 48℃ Temperature at evaporator, T2…

Q: 14. What is the difference between unidirectional and bidirectional associativity? 15. Define an…

A: 14.      The bidirectional associativity that exists across all of these environments means that any…

Q: Examine the following open gas turbine process. The temperature of the inlet air is 292 K and…

A: Given:The temperature of the inlet air, The pressure of the inlet air, The polytropic efficiency of…

Q: grass chipper machine)

A: The grass chipper is a newly developed equipment that combines the duties of chaff cutting and…

Q: For this question, down is defined as the positive direction and up is defined as the negative…

A:

Q: Task 1 It is required to design a tennis ball for recreational use by settlers on Mars. The primary…

A: Given data:LE - Drop height on Earth (m) = 2.54 m gE - Gravitational acceleration on Earth (m/s2) =…

Q: The part view should be the same as picture. 2- The color is RGB as 0,220,100. 3- Should use the…

A: Find Draw the given object using the drawing.

Q: Using autocad draw necessary views. Kindly all the views I'll rate your solution

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Question (1): according to the graph shown, the sample length is 100 mm and the graph is drawn to a…

A: When we are producing components by various methods of manufacturing process it is not possible to…

Q: Create me a simplified cash flow diagram for the project starting from initial development until the…

A: Phase 3: First Month of SalesFixed Costs (same as Phase 2)Variable Costs (estimate per unit…

Q: Read the article: Age-related slowing of response selection and production in a visual choice…

A: This article is based on the title of the article, "Age-related slowing of response selection and…

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: Step 1:

Q: A completed performance review shows that the scores of a company's newest product fall in the…

A: If the company's newest product falls in the bottom left segment of the Kano model, it means that…

Q: Please do not rely too much on chatgpt, because its answer may be wrong. Please consider it…

A: For instance a vertical pipe filled with liquid. We want to find the pressure at a specific point…

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.