18 A single-cylinder, two-stroke cycle model airplane engine with a 7.54-cm displace ment produces 142 kW of brake power at 23,000 RPM using glow plug ignition. The square en- gine (bore stroke) uses 31.7 gm/min of castor oil-methanol-nitrome thane fuel at an air-fuel ratio AF = 4.5. During intake scavenging. 65% of the incoming air-fuel mixture gets trapped in the cylinder, while 35% of it is lost with the exhaust be fore the exhaust port closes. Combustion efficiency n = 0.94. Calculate: (a) Brake specific fuel consumption. [gm/kW-hr] (b) Average piston speed. [m/sec] (c) Unburned fuel exhausted to atmosphere. [gm/min] (d) Torque. [N-m]

18 A single-cylinder, two-stroke cycle model airplane engine with a 7.54-cm displace ment produces 142 kW of brake power at 23,000 RPM using glow plug ignition. The square en- gine (bore stroke) uses 31.7 gm/min of castor oil-methanol-nitrome thane fuel at an air-fuel ratio AF = 4.5. During intake scavenging. 65% of the incoming air-fuel mixture gets trapped in the cylinder, while 35% of it is lost with the exhaust be fore the exhaust port closes. Combustion efficiency n = 0.94. Calculate: (a) Brake specific fuel consumption. [gm/kW-hr] (b) Average piston speed. [m/sec] (c) Unburned fuel exhausted to atmosphere. [gm/min] (d) Torque. [N-m]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(e) Calculate the angular velocity of the gas mixture sing paddle wheel model of two- cylinder engine by assuming swirl ratio is 11. Use the following data: i. air to fuel ratio 8.8 ii. compressiom ratio-7.2 ii, volunetric efficiency77 iv. indicated thermal efficiency 33 v. mechanical efficiency55 vi. brake power 62000 j/sec vii. engine volmne 1000 cm3 vi. calorific value 45000 kj/m
Please show the complete step-by-step solution in a clear manner. Thank you!
Pls explain clear and derailedDefine:Internal Combustion Engine Compare and contrast. 1. Otto Cycle2. Diesel Engine
State 1 for dual combustion engine id P1 = 1 atm and T1 = 61oC; rk = 18; at the end of the constantvolume combustion process the pressure is 7700 kPa, rc = 1.5. Base on 1kg/cycle of a hot air standard with k = 1.31, determine a.) the percentage clearance, b.) the pressure, temperatures at each corner point on the cycle, c.) Wnet and d.) the thermal efficiency.
For a sprak ignition engine the following readings were observed. cylinder diameter 10 cm, stroke length 10 cm and clearance gap between TDC and cylinder head is 10 mm. for such engine the compression ratio will be а. 11 O b. 10 c. 100 d. 110
Q.1 formula (CH19O..1) produces 300 Nm @ 2400 rpm. The displacement volume of the engine is 2 litres and A 4-stroke, 4-cylinder diesel engine operating with bio-diesel fuel with an equivalent molecular the intake air flow rate is 69.6 g/s. LHV of fuel is 41 MJ/kg. Measurement of the engine exhaust gives the following volumetric concentrations: 200 ppm CO 32 mg soot / m of exhaust Assuming a brake thermal efficiency of 40%, density of exhaust as 1.15 kg/m' and molar mass of exhaust as 29 kg/kmol, determine the soot and CO emissions in g/kWh
For a 4-stroke, SI engine with the following parameters: crank angle degree (CAdeg ATDC), 20 start of combustion (soc) crank angle degree: -10 CAdeg ATDC burn duration: 40 CAdeg Calculate the mass fraction burned (between 0 to 1) based on the Wiebe function. (assume a=5 and m=2) Give your answer to 2 decimal places.
Discuss the importance and benefits of air standard cycle analysis in engine componentsdesign. Provide at least three key points and justify your answers.
a. Discuss the different parameters being analyzed in the overall performance of the engine b. What is the difference between RFG and RFS? c. Explain the difference of the combustion processes involved between SI and CI engines?
please send handwritten solution Q3 part b
Some operating data for an air-standard Otto cycle are given in the table. Use the operating data to answer the questions below. ? (???) ? (?) ? (??^3) 1 1 300 400 2 - - 40 3 - 1500 40 4 - - 400 a) Sketch this Otto cycle on a ?-? diagram. Label what you can on the diagram given the information in the table, then come back and modify your diagram with the information you determine in partb) Fill in all the missing pieces of information in the table.
write step by steps