17-45. The drop gate at the end of the trailer has a mass of 1.25 Mg and mass center at G. If it is supported by the cable AB and hinge at C, determine the tension in the cable when the truck begins to accelerate at 5 m/s?. Also, what are the horizontal and vertical components of reaction at the hinge C? 30 1.5 m 45°

17-45. The drop gate at the end of the trailer has a mass of 1.25 Mg and mass center at G. If it is supported by the cable AB and hinge at C, determine the tension in the cable when the truck begins to accelerate at 5 m/s?. Also, what are the horizontal and vertical components of reaction at the hinge C? 30 1.5 m 45°

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A horizontal 4.0 m long 5.0 N uniform bar at one end is attached to a wall by a frictionless hinge; and at the middle of the bar there is a vertical cable pulling down 7.0 N, and at the middle of the bar there is also a cable that is at 45 ° to the horizontal pulling up as shown. ii) What is the magnitude of the horizontal component of the force on the bar due to the hinge?
Please answer fast
R8-7. The uniform 50-lb beam is supported by the rope that is attached to the end of the beam, wraps over the rough peg, and is then connected to the 100-lb block. If the coefficient of static friction between the beam and the block, and between the rope and the peg, is us = 0.4, determine the maximum distance that the block can be placed from A and still remain in equilibrium. Assume the block will not tip. 1 1 ft 10 ft- Prob. R8-7 المسوحة فولا CamSearer
g I e n 0 g er e CO Mk nd he ute the sa or a nd? *13-44. If the motor draws in the cable with an acceleration of 3 m/s², determine the reactions at the supports A and B. The beam has a uniform mass of 30 kg/m, and the crate has a mass of 200 kg. Neglect the mass of the motor and pulleys. 2.5 m 3 m/s² 0.5 m 3 m Prob. 13-44 B
Determine the force in member BE of the loaded truss. The force is positive if in tension, negative if in compression. D 5 KN 8 KN 2 KN 2 m 2 m B 2 m A Answer: BE = i E -4 m F kN
help pls
2. A 3.0-m-long ladder leans against a wall at an angle of 60° with respect to the floor. What is the minimum value of us, the coefficient of static friction with the ground, that will prevent the ladder from slipping? Assume that friction between the ladder and the wall is negligible. Center of gravity 19 TULO L 60⁰ Weight acts at the center of gravity. Known L-30 m Find Me Contro <= 0 about this point. Static friction prevents slipping.
The total mass of cable ACB is 20 kg. Assuming that the mass of the cable is distributed uniformly along the horizontal, determine (a) the sag h, (b) the slope of the cable at A.
Needs Complete typed solution with 100 % accuracy.
Determine the x-y and n-t components of the 33-kip force F acting on the simply-supported beam. F = 33 kips I 12' B 20' Part 1 19° 30 Find the angle B. t 33 kips 30° K 19° Answer: 3 = i n x n
11-30 Two blocks are suspended on a continuous inex- tensible cord as shown in Fig. P11-30. Determine the angle O for equilibrium if the masses of blocks A and B are 50 and 40 kg, respectively. Fig. P11-30
Determine the resultant R (single equivalent force) of the three forces acting on the simple truss. Specify the points on the x-andy- aces through which R must pass 17 KN A Answers: R=(4 138 23 KN 24 KN EE DKN