17-103 Air enters a rectangular duct at T₁ = 300 K, P₁ = 420 kPa, and Ma, = 2. Heat is transferred to the air in the amount of 55 kJ/kg as it flows through the duct. Disregarding frictional losses, determine the temperature and Mach num- ber at the duct exit. Answers: 386 K, 1.64 55 kJ/kg P₁ = 420 kPa T₁ = 300 K Ma₁ = 2 Air

17-103 Air enters a rectangular duct at T₁ = 300 K, P₁ = 420 kPa, and Ma, = 2. Heat is transferred to the air in the amount of 55 kJ/kg as it flows through the duct. Disregarding frictional losses, determine the temperature and Mach num- ber at the duct exit. Answers: 386 K, 1.64 55 kJ/kg P₁ = 420 kPa T₁ = 300 K Ma₁ = 2 Air

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air enters a nozzle that has an inlet area of 0.4 m?, at 200 kPa, 500 °C. and 30 m/s. At the exit the conditions are 100 kPa and 443 °C. Part A If the exit area is 45 cm? , determine the steady-state exit velocity. Use the IG flow-state TESTcalc. Express the steady-state exit velocity in meters per second to four significant figures. ΑΣφ vec ? V. = m/s Submit Request Answer
stagi 900 kPa 1- Air enters a compressor for a mass flow rate of 0.04 kg/s. at a stagnation temperature 358 K. Assuming the AIR compression process to be isentropic, determine the power 0.04 kg/s require. 100 kPa stagnation
Air enters a 5-cm-diameter, 4-m-long adiabatic duct with inlet conditions of Ma1 = 2.8, T1 = 380 K, and P1 = 80 kPa. It is observed that a normal shock occurs at a location 3 m from the inlet. Taking the average friction factor to be 0.007, determine the velocity, temperature, and pressure at the duct exit.
What is the effect of friction on the entropy of the fluid during Fanno flow?
A nozzle operates with steam entering at 700 kPa and 300 °C. The velocity at the inlet is 30 m/s. As the steam flows through the nozzle, the pressure decreases. Determine the area ratio value (Area / Area inlet), where Area inlet is the cross sectional area of the nozzle at the inlet, at the sections of the nozzle where the pressure values are 650, 550, 450, 350, and 250 kPa. Assume nozzle operates isentropically.
Find the center of mass of the structure given in the figure below. Assume a uniform thickness of 20 cm, and a uniform density of 1 g/cm3.
I need help on 3b
Argon is accelerated in a nozzle from 32 m/s at 666 K to 441 m/s and 196 kPa. If the heat loss is equal to 5.1 kJ/kg, determine the gas temperature at outlet in K to 1 decimal place. Take the gas constant as 0.2 (kPa m3)/(kg K) and assume constant specific heats cp=0.5 kJ/(kg K) and cv=0.3 kJ/(kg K).
Air exits from a reservoir maintained at 15 °C and 400 kPa absolute into a receiver maintained at (a) 200 kPa absolute and (b) 100 kPa absolute. If the exit area is 0.001 m², by using equations determine the mass flow rate.
I need help on 3a
Q3- Air flows from a reservoir and enters a uniform pipe with a diameter of 0.05 m and length of 10 m. The air exits to the atmosphere. The following conditions prevail at the exit: P2 = 1bar, temperature T2 = 27°C and M2 = 0.9. Assume that the average friction factor to be f = 0.004 and that the flow from the reservoir up to the pipe inlet is essentially isentropic Estimate the total temperature and total pressure in the reservoir under the Fanno flow model. %3D M2 0.9 D-0.05 m] L=10 m Po=? To=C T2-27°C P2=1|Bar]