16.40 An 8-bit A/D converter has a reference voltage of 10 V. Find (a) the analog input corresponding to thebinary outputs 1010 1010 and 0101 0101, (b) the binary output if V₁ = 3 V, and (c) the resolution of theconverter.Serial data inputAnalogvoltageoutClock>ComparatorVaVbV₁DQ₂B₁▲ Analog input8-bit SARQ38-bit DACDOSCCQoBo(b) 8-bit A/D converterLatchenableE8-bit latchSerial data outStart conversionConversion completeBinary inputsDigitaldataoutput

The analog signal can be converted into digital signal by using the ADC converter. The conversion…

16.40 An 8-bit A/D converter has a reference voltage of 10 V. Find (a) the analog input corresponding to the binary outputs 1010 1010 and 0101 0101, (b) the binary output if V₁ = 3 V, and (c) the resolution of the converter.

16.40 An 8-bit A/D converter has a reference voltage of 10 V. Find (a) the analog input corresponding to the binary outputs 1010 1010 and 0101 0101, (b) the binary output if V₁ = 3 V, and (c) the resolution of the converter.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 16-bit Successive Approximation A/D converter converter (0-3.3 V) has 12 MHz clock. It takes 4 clock cycles to make a single comparsion. How much time does it take to covert a 5.6 V signal to a digital output? a.5.8 microseconds b.0.51 microseconds c.5.3 microseconds d.13.3 microseconds e.4.85 microseconds
Design 3bit gray to Binary converter using k-map
Plz I need the answer of this question in digital system design
In a stair step A/D converter, clock frequency is 1 MHz, threshold voltage is (0.1 V). The full scale output of D/A converter is (10.23 V). If it is a 10 bit device. Find the conversion time for an analog input of (3.728 V)? 373 UG
Which is the output function F for the digital circuit shown in the figure is correct?
An AlD converter has full Scale output of the DIA 8-bit input. ine a clock fasuenay of 100k H2. 8.455 volts with The is comparator thershold Vo(tage is VA = 4.562 voff (Analoy vo (tage) delermine from the counter? 1mv. if the digital number obtain ed @) 123 140 O 138 (d) 98 () 112 (f) None of these.
2- Design a 4-bit DAC assuming high voltage of 3.5 V and a Vee of 12 V? determine the output voltage when the input is 1010? 2170 18.
21. Ipss = 20 mA and Vgs(off) = –-6 V for a particular JFET. %3D (a) What is Ip when Vcs = 0 V? (b) What is Ip when VGs = VGs(off? (c) If Vcs is increased from -4 V to –1 V, does I, increase or decrease?
A 4bit D/A converter use an inverting summer as its output stage. The input voltages can be either 0 or 5 V in a binary sequence. The input resistors are as follows: R1 = 1 k, R2 = 2 k, R3 = 4 k, R4 = 8 k, and RF = 1 k. Determine the output voltage for the case where the V1 = 5 V, V2 = 5 V, V3 = 0 V, and V4 = 5 V.
An analog output voltage for the input 1001 to a 4 bit D/A converter for all possible inputs assuming the proportionality factor K=1 will be (A) 9 (B) 6 (C) 3 (D) 1
QI Ref RG RM A1 Vou VOUT Digital A DACI Input, DIN VDAC Figure QI Figure QI shows the circuit used to condition the output of the n- bit Digital to Analog Converter "DACI" having a digital input value of Dw. DACI may be assumed to have a voltage output with zero source resistance coded in "straight binary" such that • For a binary input of Dy = 000...000 the output voltage vaac is 0 V • For a binary input of Dw = 111..111 the output voltage vaac is Vn Where Vg is a positive voltage reference. Neglecting Ry and assuming that opamp Al is ideal, show that the output voltage v, is (а) OUT R. for D, - 000000 R (i) Vay- ref (ii) Vor for D,-111..111 Hence choose values of Ro and R to give an output voltage range -V Svar S (iii) Re-draw Figure Q1 to show all sources of DC opamp error and say why they have the signs you have given them. (b) Hence derive an expression for the emor in vug due to opamp DC input cur. and voltage errors including both bias and offset currents. (c) If the two…