16-5 A two-stage ammonia system using flash-gas removal and intercooling operates on the cycle shown in Fig. 16-1 2a. The condensing temperature is 35°C. The satura- tion temperature of the intermediate-temperature evaporator is 0°C, and its capacity is 150 kW. The saturation temperature of the low-temperature evaporator is -40°C, and its capacity is 250 kW. What is the rate of refrigerant compressed by the high-stage compressor? Ans. 0.411 kg/s

16-5 A two-stage ammonia system using flash-gas removal and intercooling operates on the cycle shown in Fig. 16-1 2a. The condensing temperature is 35°C. The satura- tion temperature of the intermediate-temperature evaporator is 0°C, and its capacity is 150 kW. The saturation temperature of the low-temperature evaporator is -40°C, and its capacity is 250 kW. What is the rate of refrigerant compressed by the high-stage compressor? Ans. 0.411 kg/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A. Describe the four processes, which occur in the vapor-compression-refrigeration cycle that youtested.B. How did you figure out the enthalpy at the various entry / exit stages? (I know you lookedat the chart or table provided! I understand that you may have used interpolation.) I want you toexplain briefly how you determined, what principle(s) you used to determine the enthalpy at thevarious points.Sketch a p-h diagram. On this sketch of the p-h diagram you must sketch and show SOME constanttemperature lines, constant pressure lines, constant enthalpy lines, constant entropy lines, quality factorand other significant features of the p-h diagram to show your understanding of the p-h diagram. Labelx & y axis, indicate the units, indicate the critical point. Label various regions,
Provide a technical design outlining the ideal refrigerant and operating parameters for a three-stage closed-type cascade refrigeration system that will run with a 150TOR load at -40°C evaporator and 65°C condensing temperatures. Imagine that your isentropic compression is 74% effective.Draw the engaging temperature as well so that the heat exchange interfaces differ by 5°C. Please draw detailed. explain Please. It would be a great help.
Please do all the parts (a,b, and c ), I really need them. Please Full steps and make sure your handwritten is CLEAR & BIG, please THANK YOU SO MUCH
B-Draw the ideal vapour compression refrigeration cycle on T-S and P-H diagrams. State all details on the diagrams and give a short explanation of each process of the cycle.
Cold storage uses R134a, the evaporator temperature is -7C and the condenser temperature is 32C. The cooling load is 5.3103 kJ/min. The cycle is ideal. Determine: 1. Mass flowrate of the refrigerant. 2. Coefficient of Performance (COP). - If the water condenser is used that enter at 24C and exit at 30C. determine the water flowrate.
your client needs to know about the mass flow rate ofsteam needed for a 1500 kW plant. The heat supplied to the steamin the boiler is 2700 k//kg, the heat rejected by the steam to thecooling water in the condenser is 2000 kJ/kg, and the feed pumpwork required to pump the condensate back into the boiler is 3.5 kWCalculate the mass flow of steam required
A Rankine cycle is executed with steam expanding initially from 20 MPaa and 100 deg SH.Condensation occurs at T = 86.49 degree Celsius. All expansion and compression efficiencies are 90 %.Sketch the equipment layout and the TS diagram. Answer the following for (m = 10 + SN/10 ) kg/sec of steam circulated and fill up the blanks in theitems below:1. TS diagram with the cycle showing correct location of points with respect to saturation domeline with ne and nc = 90%.2. If the generator efficiency = 95%, brake engine efficiency = 90% what is the brake work in KW?Answer: ______________________3. Actual Steam Rate for the engine in Kg/KW-hr with efficiency values at item 2. Answer: _________________________
Complete the Table shown below to include R134a. Based on the data in whatrefrigerant can R134a be a substitute? Explain your answer.
please answer 6 to 10
Compare briefly the relative merits of a shell-and-tube condenser with a cooling tower, and an evaporative condenser. Make a sketch of an evaporative condenser, indicating the main components.
Question 2: (a) The pressure at which the steam should be reheated. (b) The thermal efficiency of the cycle. (c) Total heat input (Qin) (d) Total turbine work output (Wtur.out) (e) Draw the T-S diagram Notes: Assume the steam is reheated to the inlet temperature of the high-pressure turbine. • The moisture content of the steam at the exit of the low-pressure turbine is not to exceed 9.5% Boiler 650 C 17.5 MPa ww Reheater High-P turbine P₁ = Ps= Preheat Pump Low-P turbine Condenser e 15 KPa