16-4 A refrigerant 22 system has a capacity of 180 kW at an evaporating temperature of -30°C when the condensing pressure is 1500 kPa. (e) Compute the power requirement for a system with a single compressor. (b) Compute the total power required by the two compressors in the system shown in Fig. 16-17 where there is no intercooling but there is flash-gas removal at 600 kPa. Ans. 60.7 kW

16-4 A refrigerant 22 system has a capacity of 180 kW at an evaporating temperature of -30°C when the condensing pressure is 1500 kPa. (e) Compute the power requirement for a system with a single compressor. (b) Compute the total power required by the two compressors in the system shown in Fig. 16-17 where there is no intercooling but there is flash-gas removal at 600 kPa. Ans. 60.7 kW

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Why would a pump experience cavitation?
What common type of compressor have you encountered in your existence? Briefly discuss its application
An air compressor forms a, O A. closed system O B. combined open and isolated system O C. open system O D. isolated system
Differentiate compressor, fan, and blower.
1. In the bulk modulus of water is 2.2 GPa, what pressure is required to reduce its volume by 0.6 percent?a. 11 c.13b. 14 d.12 2. Water in a hydraulic press is under a pressure of 92.580 MPa abs. at 16 degrees C. if the initial pressure is 150Kpa abs., what will be the decrease in specific volume if it’s bulk modulus is 2.13 GPa?a. 3.22% c.5.34%b. 4.82% d.-4.34% 3.A certain gas at 30 degrees C is subjected to a pressure of 200kPa abs. if it has a volume 35 L, compute the mass of this gas. Use gas constant. R=210 N-m/kg-“K.a. 0.11kg c.0.97kgb. 0.23kg d.1.12kg
An air compressor in Albuquerque with an 8-gallon tank is initially at atmospheric pressure (12.2psia, zero gauge pressure) and 60°F. The compressor is turned on and the tank gauge pressure iselevated to 120 psig. At the end of the pumping interval the air in the tank is at 120°F.a) How much air (lb mass) was added to the tank?b) What will the gauge pressure be in the tank after it cools back down to 60°F.
7
(b) In Figure Q5, the 17 kg of circular disk is originally rotating with a clockwise angular velocity, o = 49 rad/s at the end of the link BC. Given the kinetic coefficient of friction, uk = 0.25 when the disk is then placed against the wall. (i) Draw the kinetic diagram of all forces exerted on the circular disk. (ii) Calculate the force of link BC. (iii) Calculate the angular acceleration of the circular disk. (iv) Calculate the time required to stop the motion of the circular disk,
Three types of fluids stack in an open tank as shown in the plot. Select the expression of the gage pressure at location 1, P1(gage)=______ A. Patm B. 0 C. 101.325 kPa D. It can not be determined.
Explain basic sauna and steam room installation.
Figure P.16.10 shows a plane truss pinned to a rigid foundation. All members have the same Young's modulus of 70 000 N/mm² and the same cross-sectional area, A, except the member 12 whose cross-sectional area is 1.414A. Under some systems of loading, member 14 carries a tensile stress of 0.7 N/mm². Calculate the change in temperature which, if applied to member 14 only, would reduce the stress in that member to zero. The coefficient of linear expansion a=24x10-/º C. Ans. 5.5°.
PROPERTIES OF MOIST AIR / SENSIBLE HEATING / SENSIBLE COOLING