15mg per kg body weight  25mg per 1cc 5.5lbs give: ____ cc

Q: m/s" that means the flow is: In a horizontal flow of incompressible fluid along a constant pipe…

A: In a horizontal flow of incompressible fluid along a constant pipe section under steady conditions,…

Q: The A kg collar is initially at rest on the bar at position 1 as shown in Figure Q2. The coefficient…

A:

Q: A 200 Kg box

A: Given: m=200 kgP=70 kgμ=0.36g=9.8 m/s2

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: 8 In a 2 m long pipe the cross-sectional area A-0.4 m². At a given instant a discharge of 0.48 m/s…

A: Given that: length of pipe = L = 2 mcross-sectional area of pipe = A = 0.4 m2Discharge =Q = 0.48…

Q: 3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm…

A:

Q: ood day. I am trying to review for examinations and require assistance for these questions... Horse…

A: Given

Q: Engine has a capacity of 20 milliliters per cylinder and the length of the axle arm is 5 cm Find the…

A:

Q: shown in Fig. 2-13.2a. The inscribed grid with each square having a length of 1 ft locates each…

A:

Q: 2.91 The rigid bar AOB is pinned at O and connected to aluminum and steel rods. If the bar is…

A:

Q: 350 lb 30 250 lb

A:

Q: 30 kN | 50 kN D A BA 1m - 3 m - 2 m

A:

Q: a)The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is…

A: Given data: -  The number of cylinders is n = 6. The bore of each cylinder is D = 45 mm. The stroke…

Q: CG 50 in 75 in A=? B=100 lbs C=100 lbs

A:

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: Calculate the internal normal force in section a-a. Your answer Calculate the internal shear force…

A: Given: The loaded beam is shown below:

Q: The steel rod shown below is 2inches in diameter and is subjected to an eccentric 2000 lb load…

A: Given Data: The eccentric load is P = 2000 lb. The eccentricity is e = 1". The diameter of the…

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Q: What is the x component of weight?

A: The mass of the block is m. The angle of slope from the horizontal is θ.

Q: F1: 9 kN, F2: 81 kN

A:

Q: Replace the force system with a single resultant force. Let F = [F] lb. ) Determine the location x,…

A: Given  Force, F1 = 3500 lb            F2 = 5500 lb            F3 = 1750 lb Find   Location, x

Q: - 2- 45 100lbs/ft 300lb 30 200lbs

A:

Q: .Q21 The forces do not cause rotation

A: The concurrent forces traverse through a similar point. It means that other forces balance each…

Q: find the length of (20mm) diameter bore is equal to that in the (30 mm) diameter bore,

A:

Q: A vertical cylinder of 60 mm diameter is penetrated by another cylinder of 40 mm diamet the axis of…

A: A vertical cylinder of 60 mm diameter is penetrated by another cylinder of 40 mm diameter, Q2. the…

Q: A 4 stroke 4 cylinder car engine of 4 L. What will be the swept volume of each engine?

A: Given:A 4 stroke four cylinder  has a swept volume of 4litre(L)Since nothing else is mentioned we…

Q: What is the Young’s modulus in GPa

A: Calculate the initial length. Li=50.8 mm Calculate the average of final lengths. Lf=53.6416 mm

Q: There is a robot arm. Part AB is rotating in the vertical plane with the same w0=1.2 rad/s all the…

A:

Q: The displacement of a piston in cubic inch with a cylinder bore of 7.62-cm and the stroke is 3-

A: Given:d=7.62 cml=3 in

Q: For the beams below, determine the location of the maximum deflection using double integration…

A:

Q: F3 = 52 lb 13 12 F1 = 80 lb 25°

A: Given that, The component of forces in the x-direction,

Q: For the acceleration equation, when the term VdV/ds-2 m/s² that means the flow is: In a horizontal 0…

A: