*15-8. If the bearing pads at A and B support only vertical forces, determine the greatest magnitude of the uniform distributed loading w that can be applied to the beam. a = 15 MPa, Taon= 1.5MPu. I5 mm 150'mm 25 mm

Q: Determine the force in member BF. The force is positive if in tension, negative if in compression. B…

A:

Q: 1.200 m 2 #25 250 mm

A:

Q: 35 - In the plane truss system, the loading status of which is evident in the figure, the support…

A: Analysis of truss can be done by method of joint or method of section. The forces acting internally…

Q: d)Determine the corresponding bearing stress in each support bracket at C in MPa.

A:

Q: The frame is subjected to the load of 15 kN which acts on member ABD at D. Determine the required…

A:

Q: take a =12.5 40.a mm 300 mm S-3) Find the diameter of the pins B and D (B single cut D double cut),…

A:

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: E=200GPa To find value of P

Q: Find the moment capacity MR = M, of a beam with: %3D b = 20 in %3D h = 34 in 8- #7 bars # 4 stirrups…

A:

Q: Situation C. The lap joint shown below is fastened by four 4-in.- diameter rivets. Shearing stress…

A:

Q: QUESTION 6. D 5A SA

A:

Q: If h=3ft and d=5ft, find the force in members BE and BC

A: To find force in member BE and BC

Q: Sketch the elastic curve for the frame as shown. 2 m--

A: We have to sketch the elastic curve for the frame.

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

A:

Q: Determine the weight of 8m simply supported 200mm x 500mm rectangular beam whose allowable flexure…

A: Given data,  Width of beam = 200 mm Depth of beam = 500 mm Stress in beam = 22 MPa.  L = 8 m To find…

Q: Set P₁14 kN and P₂ = 9 kN. (Figure 1) Figure F z B 2 m A 1 m 2m 1 of 1 1m D

A: Given data - P1 = 14 KNP2 = 9 KN Find out - Force in the members of the truss.

Q: The steel block shown in is subjected to a compressive force on all directions. Determine the change…

A: Given that:                    E=210x103 N/mm2 μ=0.28Change in length of y-direction,…

Q: 600 -N.A. As=1000MM? 200 350

A: The acceptable limit for the safety and serviceability requirement of a structure of element before…

Q: 1a/Assume the support at A and B or D are pins

A: The objective of the question is to understand the forces acting on a structure and how they are…

Q: A load of P = 5778 N is acting on member AC. The length of AC is d = 437 mm. The cross-sectional…

A:

Q: Consider the truss system below supported by a pin support at A and a roller support at F. Solve for…

A:

Q: Both sections are made of steel with E-200 GPa. The gap between the bottom of the metal bar and the…

A: Given data: Length of section AB, L1=300 mm Length of section BC, L2=300 mm Area of section AB,…

Q: Determine force in member AB

A:

Q: The bent bar structure ACDE is supported by ball-and-socket joint at A and E, and by the wire DF.…

A: Given:- A ball-socket-joint is provided at point A The magnitude of the load (P) = 640 N  The…

Q: QUESTION 4) In the frame system in figure, the diameter of pin at joint B is d. The allowable shear…

A:

Q: The load on the bearing of a cast-iron bracket is 5 kN. The form of the section AB is given.…

A:

Q: 800lb 60 12' 12 FORCE Ibs A MA= Fxd Couples F= F.Cos( e ) F= F.Sin( e) Forces 100lb/ft

A: Given data  Point load and UDL Length of span.

Q: Determine (approximately) the bar force in member Al (in kN). Assume the diagonals cannot support a…

A: An overhanging truss on both sides with three concentrated loads of , , and at joints J, H, and…

Q: The member is loaded with load P as shown. a) Find the stress at points A,B,C and D b) the points…

A: Question is based on the section subjected to the point load. Magnitude of load and dimension of…

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: Given  a= 1.75m, b=1m, d = 50mm, h=10mm

Q: (a) the beam deflection (b) the beam deflection at point A. at point B.

A: Given- a cantilever beam carrying point load and concentrated moment Required-to find deflection of…

Q: A K D 2m 4 kN C E 0.5 m ↓ 0.5m 2m B

A:

Q: Determine the shear value when x = 6m (from the left) for the beam shown Where: P1 = 61kN; P2 =…

A: Equipibrium equation in x direction and in y direction  Cut the plane from left end at 6m end and…

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: given : a=1.5 m b=1 m d=30mm δC=8mm

Q: ated plastic beam of square cross section glued togethe own. The beam has a total weight of 10 N/m…

A: w = q×l ⇒ = wl= 4400 q = 0.01 n/mm

Q: Q/The force in the member (CA) is 12m 50 kg 490.50 N 500.44 N 200.12 N 2550 N 5m BX In your hand

A:

Q: The crowbar is subjected to a vertical force of P = 27 Ibat the grip, whereas it takes a force of F…

A: Given : P = 27 lb at the grip and F = 160 lb at the claw To Find : Moment of force P about A Moment…

Q: In the plane truss system, the loading status of which is evident in the figure, the support…

A: Draw the free body diagram.

Q: Determine the force in member EF for the truss shown using the method of joints. 40 kN 40 kN 40 kN…

A:

Q: The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum…

A: