150cfm of saturated air at 85F dry bulb temperature is adiabatically mixed with 75cfm of air at 65F dry bulb temperature and 30% relative humidity. The mixture dry bulb temperature is most likely 67F 72F 75F 78F 80F OO

Q: I need help matching the parts of the print to the terms.

A: Tolerance block will go with choice E.

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: Q- In a limit System, the following limits are Specified for hole and shaft. calculate the tolerance…

A: The limits of the hole are..The limits of the shaft are..

Q: From the following identify  the false statement . In general safety precaution the machine should…

A: Precaution and safety

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: I need help with question number 15 that is pertaining to the print provided.

A: 15.The unidirectional system is used here for the dimension placing. The unidirectional system is…

Q: & Sharpe gears är ne differential indexing formula, calculate the indexing for the following: EROWN…

A: Given, Simple indexing Gear ratio 40:1 Number of divisions(N) =35   40 revolution of crank=1…

Q: Use the prefix multipliers to express cach measurement without any exponents. 22 x 10-15s

A: Given: The time is t=22×10-15 s. The unit conversion factor to convert Second into Femtosecond is, 1…

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: -0.0025 1. The dimensions for the shaft size are o50-0.0037 mm and the hole size are +0.000 mm. Find…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: I want to buy a two METAL SPUR GEAR for my 2 pieces of G.I pipe with an 3 inches diameter (3mm…

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Q: I need help solving problem numbers 4--15.

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

A:

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…