15.8 a) Use the circuit in Fig. 15.4 to design a high-pass filter with a cutoff frequency of 2.5 kHz and a passband gain of 10 dB. Use a 50 nF capacitor in the design. DESIGN "ROBLEM b) Draw the circuit diagram of the filter and label all the components.

15.8 a) Use the circuit in Fig. 15.4 to design a high-pass filter with a cutoff frequency of 2.5 kHz and a passband gain of 10 dB. Use a 50 nF capacitor in the design. DESIGN "ROBLEM b) Draw the circuit diagram of the filter and label all the components.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

15.10 Design an op amp-based high-pass filter with a cut- off frequency of 10 kHz and a passband gain of 4 using a 75 nF capacitor. a) Draw your circuit, labeling the component val- ues and the output voltage. b) If the value of the feedback resistor in the filter is changed but the value of the resistor in the forward path is unchanged, what characteristic of the filter is changed?
C R₁ M Rf www + Vo For the op-amp filter circuit shown above, assume C₁ = 10nF, R₁ = Find the corner frequency, wc, of the circuit. 1k, and Rf = 5kQ. Wc sec
4. Three of the point charges are placed on the x-axis as shown in figure. Find the net force in the middle charge due to the two other charges. 3.0 μC -5.0 μC 8.0 μC 20 cm 30 сm FE3 FE8
Analogue Electronics II Design 2 different configurations of active band pass filter for the frequency with bandwidthof 200 Hz.Design A has the quality factor Q less than 10, is independent on the critical frequency,whereas Design B has the quality factor, Q more than 30, is dependent on the criticalfrequency. You can use your own value of resistors and capacitors in the design. Show allrelated calculations (eg. fc, fo, Q, Gain, Bandwidth) and the final circuit design.
DESIGNPROBLEM_PSPICEMULTISIM Use a 500 nF capacitor to design a bandreject filter, as shown. The filter has a center frequency of 4 kHz and a quality factor of 5. 1. a) Specify the numerical values of R and L. 2. b) Calculate the upper and lower corner, or cutoff, frequencies in kilohertz. 3. c) Calculate the filter bandwidth in kilohertz. Vi 500 nF HE L R Vo
Parameter Value Gain, AV 30 dB Resistor, R1 1.5 kΩ Capacitor, C 3.35 uF 1. Figure depicts a first order low pass filter and Table tabulates parameters ultised to construct the filter. In the design, R1||R2. Calculate the bandwith of the filter. 2. Describe the condition of unity gain in an amplifier and determine voltage output, VO,if voltage input, V1, is 2V for a non-inverting amplifier 3. Construct an equation relating the input (Vin) and output (Vout) of an inverting amplifier.The conditioning circuit has input range between 10 mV to 110 mV which resultingoutput between 0V to 5V.
I need the answer as soon as possible
H.W2: a) Using 0.1 µF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jwo)where wo is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at w,?
Build a 4th order high-pass filter with a corner frequency of 50 kHz and a transition that is as steep as possible. Other parameters can be freely selected.
Design a 4th order active High Pass Butterworth filter having a cut-off frequency of IKHz and pass band gain of 40DB. Plot its frequency response.
H.W2: a) Using 0.1 uF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jwo)where wo is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at wg?
Asap please