15 kN 25 kN 20 kN C В D 1 m 0.8 m 0.3 m 30 kN °0.4 m

Q: Calculate the volume of this figure providing the dimensions below, the values is all meters. how…

A: The volume of the given figure which can be used to fill sand is calculated below. Volume =…

Q: Solve for all values of x by factoring. z² – 13x = –5x %3D

A: Given, x2-13x=-5xx2-13x+5x=0x2-8x=0by factoring,x=-b±b2+4ac2ax=-(-8)±(-8)2+4(1)(0)2x=0,8or we can…

Q: 7.ON 5.0N 15 20 50 4.0N

A: To calculate the resultant force of the given system first determine the component of forces in x…

Q: ?Find the centeroid of the shaded area shown in fig 80 60 30 Dimensions in mm X= 49.2 mm and Y= 32.8…

A:

Q: 20. = 3,500 mm, w = 0.5 m A = 2 cm²

A:

Q: dx 5e²t-3

A:

Q: Determining the result and direction of two forces or more. Use the grid below to draw the force…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 5.0N 6.0N 30 10 130 3.0N

A: To calculate resultant force first calculating component of force in x and y direction as follows –…

Q: What is the rate of flow of water passing through a pipe with a diameter of 1944 mm and a speed of…

A:

Q: Figure 1. Length of line AC? a. 8.33" b. 5.83" c. 9.72" d. 11.33"

A:

Q: Q3) Determine the x- and y-coordinates for the shaded area as shown in figure (3), noted that all…

A:

Q: 1. What is velocity of B if velocity of A is 10 in/s downwards? Show all work. C B

A: The velocity of 'A' is given as 10 inchess. The velocity of 'B' needs to be evaluated.

Q: Q3) Determine the x- and y-coordinates for the shaded area as shown in figure (3), noted that all…

A:

Q: Draw the velocity diagram

A: Given:To find:Draw the velocity diagram.

Q: 500 Gu Delermine the moment a bout Point (0) 610 as Shown

A:

Q: u 30° 40° F = 600 N 22

A:

Q: Q.1) Compute I, and k, for the two area by dividing it into rectangles 1 and 2 as shown. m

A: Given: Length of the each rectangle=3 m width of the each rectangle=1 m

Q: Briefly explain the gravity die casting process with a neat diagram

A: Gravity Die Casting is a permanent mould casting process, where the molten metal is poured from a…

Q: ompute the moment of inertia, Ix of the crosS-sectional area about the neutral axis. + 6 in.- 6 in.…

A:

Q: Q.1) Determine Ixx, lyy and Ixy for the section shown below. y y = x 1/2. 0.6 m y = 0.36 m

A:

Q: Find the force (in Newtons) exerted on the dam by water pressure.

A:

Q: QUESTION 1 Determine the force required to hold the taper Section 2 unit of kN. Round to the nearest…

A: Data given:A1=0.01 m2A2=0.03m2V1=13.2 m/secfind out:the force required to hold the pipe

Q: Comment on accuracy and precision of the spherical ball diameter

A:

Q: What is the rate of flow of water passing through a pipe with a diameter of 1330 mm and a speed of…

A:

Q: نقطتان )2( A solid ball has a mass of 20 grams and a radius shown in micrometer. * ?What is the…

A: Given: Main scale reading, MSR= 7.5 mm. Circular scale reading, CSD= 24 mm. Mass of the ball, m=20…

Q: Use the prefix multipliers to express each measurement without any exponents. 1.5 x 10° g

A: The prefix multiplier is the symbol that is used to express large units without any exponent. There…

Q: Wire BC, has a diameter of D. and made of A-36 steel, is used to support member AB at B as shown.…

A:

Q: What is the rate of flow of water passing through a pipe with a diameter of 1616 mm and a speed of…

A:

Q: Calculate the dimension * marked in red X in the following figure 79 22 $14 8 8/8 60 34 26 X

A:

Q: A 2 46 KN C 2 B 30 kN/m 1,5 D

A:

Q: The crate in (Figure 1) has a center of gravity at G. Figure P 4.5 ft 2.5 ft 3.5 ft 1 of 1 Part A…

A:

Q: ajor principal axis of the section with respect to

A: major principal axis can be obtained as below,

Q: 01.00 1.25 - R50 2.50 1.25 Draw the side, front and auxiliary views, put all necessary dimensions…

A: Given: Component To find: front view, side view, and auxiliary view

Q: Compute the coordinates of the centroid (x, y) of the area shown.

A:

Q: Exercise 9.45 Draw the given views and develop the lateral surface.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: R20 20 30 30 40

A: According to details provided in the question. required solution is shown below by using the third…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.