15 - 30 - 15 Ø160 Ø110 Ø16 45° Ø30 Ø30 Ø40 Ø70 15 FRONT VIEW RIGHT SIDE VIEW

Q: LESSON: AUTODESK AUTOCAD Choose from the choices:

A: The broken line is used to draw the large drawings which are not possible to draw on the sheet,…

Q: 45° 50 33 80 Ø32

A: This type of problem is not solved by us. I have given you the hint to solve the problem please…

Q: Sketch the figure using AutoCAD and hatch the lines with colours . mention the dimesions as shown in…

A:

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

A:

Q: ?What is the final reading of Vernier caliper from the figure given below 10 30 40 50 20

A: The main scale reading =5mm Vernier scale reading=0.775mm

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: Draw the isometric view of the following object given in orthographic projection.

A:

Q: Draw the orthographic views of the following isometric figure.

A:

Q: COMPLETE THE ORTHOGRAPHIC AND ISOMETRIC VIEWS BELOW.

A: To find:Orthographic and isometric views.

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: It is a precision instrument with a low least count, and is used to take sub-millimeter dimensions…

Q: Draw the orthographic views of the following isometric figure

A: Given  3D model isometric view To find Orthographic view

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: 76°10' 0.500 DIA 45°00'- 1.125 DIA 1.000 0.875 Find length x in the accompanying figure.

A: Given figure can be redrawn as:

Q: Directions: Draw an isometric view of the following orthographic views. Views most be properly…

A: Draw an isometric view of the following orthographic views.Views most be properly aligned attached.…

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: 2 ft 2 ft 3 ft A 6 ft

A:

Q: Orthographics: Add missing lines and complete any missing views. Draw the isometric

A: The missing lines of the given views are shown below.

Q: Given two Orthographic views of an object, construct an Auxiliary view of the indicated (→→)…

A: Find Construct an auxiliary view of the object.

Q: Given the top view and right side view, draw the sectional view of the figure. Please include the…

A: Find Sectional View of the given figure

Q: Given the left and front views, sketch the top view.

A: The problem is easily done with the help of orthogonal projection. first try to imagine the 3D view…

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: The top one (first drawing) is a top view. The second one or lower one is a side view. Please draw…

A: given : top and side view

Q: Can you draw the OBLIQUE SECTION VIEW of this figure?

A:

Q: Consider FIG-DD in the appendix.   Note: For Blocks “A” & “B” & “C”: The mass of “A” is 30 kg.…

A:

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: Draw the orthographic views of the following isometric figure. (Units in mm)

A:

Q: Thank you for this answer. I don't quite understand step 4, 5 and 6 because the operation is not…

A: given; all values given

Q: 20.00 40.00 60.00 FRONT 60.00 00'0 20.00 00'0

A: If straight lines are drawn from various points on the contour of an object to meet a plane, the…

Q: Draw the isometric projection of the object showing the top, front and right side.

A:

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: In creating orthographic views, each view must:

A:

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P)…

A:

Q: What is Line G?

A: Solution:

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: Which corners would be visible from the FRONT orthographic view of this image. Select all that…

A: Front view will be like

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: Draw the orthographic views of the following isometric figure. (units in mm

A:

Q: Need you to draw orthographic views of this object.

A: The required orthographic views are drawn using third angle method of projection.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: State any three rules of orthographic parallel projection.

A: Orthographic parallel projection is a method of representing 3D objects normally by three 2D…

Q: Question: Sketch the greaphs of T and T2

A: The given question is not clear about which topic. Assumed, the graphs required related to…

Q: What line is K? A

A: What is line k

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.